Free · Calculator 6
Pipe sizing and pressure drop
Find the right nominal size from the flow rate and permissible velocity – and estimate the pressure drop of the line including fittings, valves and difference in elevation.
The task
Fast, traceable answers in piping design.
What you want
- You want all small calculations in one place.
- You want to follow every calculation step.
Our solution
- Free calculators in the browser: size and pressure drop, thermal expansion, weight, converter, tagging.
- Formulas, values and the governing criterion visible.
Your advantage
- Answers in seconds.
- Traceable in discussions.
- No installation, no login.
- Guide values with source – preliminary sizing.
Loading calculator …
Preliminary sizing, not a piping design. Dimensions and material properties come from the ASEING Piping Spec Calculator and Support Span Calculator and are estimates from publicly available manufacturer data, generalized; all other values are guide values. They may deviate from the standard – check against the applicable standards and manufacturer data before binding use. You can enter your own values in the calculator.
Basics, calculation method, examples and FAQ ▸
Basis & sources
What the tool calculates with, which standards and data it relies on and where its limits are. As of September 2026. For practice: Understand it and try it out.
Calculation method
- Velocityv = Q / A with the inside diameter of the selected series
- Frictionλ per Colebrook-White, laminar 64/Re
- LineΔp = λ·L/d·ρv²/2 + Σζ·ρv²/2 + ρ·g·Δh (Darcy-Weisbach; elevation component neglected for gas)
- Nominal sizesmallest DN with v ≤ permissible velocity (DNs to be avoided according to DIN EN 10220DIN EN 10220 – Seamless and welded steel tubes – General tables of dimensions and masses per unit length The basic table of outside diameters and wall thicknesses of steel pipes (series 1 to 3). The Piping Spec Calculator takes the outside diameter per DN from it (series 1), e.g. 114.3 mm for DN 100. Background and sources › are skipped)
- Checkexpandable under every result: calculation method with formulas, values used and sources, can be saved as PDFPDF – Portable Document Format File format for documents that looks the same on every device and can be printed – e.g. the piping class sheet. Background and sources ›
Standards & codes
Reference: the calculation is based on these standards and codes. Standard texts and tables are not included.
| EN 10220 / DIN EN ISO 1127DIN EN ISO 1127 – Stainless steel tubes – Dimensions, tolerances and conventional masses per unit length Dimension and tolerance standard for stainless steel pipes: outside diameters, wall thicknesses and the tolerance classes D and T. In the Piping Spec Calculator, the minus tolerance of the wall thickness for stainless steel is based on it. Background and sources ›, ASME B36.10/B36.19B36.10M – ASME B36.10M Steel Pipe US dimensional standard for welded and seamless steel pipes: outside diameters and wall thicknesses (schedule). Background and sources ›B36.19 – ASME B36.19 US dimensional standard for stainless steel pipe: outside diameters and wall thicknesses (schedule with “S”, e.g. 10S). Background and sources › | Pipe dimensions via the Piping Spec Calculator |
|---|---|
| DIN 11850 | Hygienic pipe |
Data & origin
| Pipe dimensions and wall thicknesses | Piping Spec Calculator (current piping spec or standard series) – estimates from manufacturer data |
|---|---|
| Water 0–200 °C | Çengel, Table A-3 (viscosity according to Sengers/Watson 1986), cross-checked against TUTU – Technical university Technical university (Technische Universität), e.g. TU Graz. Background and sources › Graz (VDIVDI – Association of German Engineers Association of German Engineers. Its VDI guidelines are regarded as generally accepted rules of technology. Background and sources › Heat Atlas) and Hydraulic Institute – deviation ≤ 0.4 % |
| Air, nitrogen | ideal gas, viscosity versus temperature according to Sutherland – deviation from table values ≤ 1 % |
| Glycol mixtures, hydraulic oil | Manufacturer data sheets (Tyfocor GE and L, 30 % by vol., 0 °C), ISO VG 46VG – Viscosity grade Viscosity grade for oils according to ISO 3448: the number is the mean kinematic viscosity at 40 °C in mm²/s, e.g. ISO VG 46. Background and sources › |
| Roughness, ζ values | Guide values, cross-checked with KSBKSB Maker of pumps and valves; its centrifugal pump handbook is a widely used source of flow data. Background and sources › and Engineering ToolBox, adjustable in the calculator |
| Typical velocities | Water discharge line 1.0–2.0 m/s (hot up to 3.5), suction line 0.5–1.5 m/s (KSB); compressed air distribution network 6–9 m/s (manufacturer data) |
Assumptions & limits
- Calculated as incompressible – gases only with a small pressure drop (below 10% of the operating pressure), otherwise section by section.
- Steam, two-phase flow and bulk solids are not covered.
- ζ values of valves are guide values – manufacturer values (ζ or Kv) take precedence.
Standards status for this page 3 standards · researched October 2026
| Standard | Contents | Current edition | Replaced / successor |
|---|---|---|---|
| DIN EN 10220 | Seamless and welded steel tubes – General tables of dimensions and masses per unit length | DIN EN 10220:2003-03 | replaces DIN V ENV 10220:1994-02; DIN 2448:1981-02DIN 2448 – Seamless steel tubes – Dimensions, masses per unit length Former German dimension standard for seamless steel pipes, withdrawn and replaced by DIN EN 10220. The outside diameters of series 1 have largely remained the same; wall thicknesses of old pipe specs often still come from DIN 2448. Background and sources ›; DIN 2458:1981-02DIN 2458 – Welded steel tubes – Dimensions, masses per unit length Former German dimension standard for welded steel pipes, withdrawn and, like DIN 2448, replaced by DIN EN 10220. Background and sources › |
| DIN EN ISO 1127 | Stainless steel tubes – Dimensions, tolerances and conventional masses per unit length | DIN EN ISO 1127:2019-03 | replaces DIN EN ISO 1127:1997-03 |
| ASME B36.10 (until 2018: B36.10M) | Welded and Seamless Wrought Steel Pipe | ASME B36.10-2022 | replaces ASME B36.10M-2018 |
Researched at DIN Media, ISOISO – International Organization for Standardization International Organization for Standardization in Geneva: it develops standards that apply worldwide (ISO standards). Background and sources ›, IECIEC – International Electrotechnical Commission International Electrotechnical Commission in Geneva: worldwide standards for electrical engineering and for instrumentation and control. Background and sources › and ASME, as of October 2026. Before binding use, please check the current edition with the standards publisher. Overview of all standards: Plant Engineering Infobase · Standards status.
Understand it and try it out
What actually happens in a pipe with water flowing through it? Friction at the wall and every change of direction cost pressure – which the pump has to supply. With the calculator you can try it out: change one value and watch what happens to the others.
The terms in five minutes
- Flow rate Q
- How much passes through the pipe per unit of time, e.g. m³/h or l/s. 1 l/s = 3.6 m³/h.
- Inside diameter di
- What matters is the inside diameter, not the nominal diameter: DN 100 in steel 114.3 × 3.6 has an inside diameter of 107.1 mm. The wall thickness is defined in the piping spec.
- Velocity v
- v = Q / A with A = π/4 · di². Half the diameter → four times the velocity.
- Reynolds number Re
- Re = v · di / ν – indicates whether the flow is orderly (laminar, Re < 2320) or swirling (turbulent, Re > approx. 4000); in between lies a transition range, which the calculator treats as turbulent to be on the safe side. In piping, flow is almost always turbulent.
- Viscosity ν
- How "thick" the medium is. Water at 20 °C: around 1.0 mm²/s, at 80 °C only 0.36 mm²/s – warm water flows more easily.
- Friction factor λ
- How much the wall slows the flow. Depends on Re and the roughness k of the wall (Colebrook-White, Moody diagram). Typically 0.015 … 0.03.
- Pressure drop Δp
- Δp = λ · L / di · ρ v² / 2 (Darcy-Weisbach) + Σζ · ρ v² / 2 for elbows and valves + ρ · g · Δh for the difference in elevation (neglected for gas).
- Head H
- The pressure drop in meters of water column: H = Δp / (ρ · g). 1 barbar – Unit of pressure Unit of pressure: 1 bar = 100,000 Pa = 0.1 MPa. In plant engineering, it usually refers to the gauge pressure relative to the surroundings (often “barg” or, in German, “bar ü”). Background and sources › ≈ 10.2 m for water. The pump manufacturer needs this figure.
Try it out and understand it
Change one value in the calculator above and watch what happens to the others:
| Try it | What happens | Why |
|---|---|---|
| Double the flow rate | Δp rises to about 3.7 times, not double. | Δp grows with v², and λ decreases only slightly with higher Re. That is why "a little more flow" quickly costs a lot of pump power. |
| Choose one nominal size larger (DN 100 → DN 125) | Δp drops to around a third, v from 1.1 to 0.73 m/s. | For the same flow rate, the diameter enters roughly to the 5th power. Larger pipes cost more material but save energy permanently – that is the trade-off when choosing the nominal size. |
| Water temperature from 20 to 80 °C | Δp becomes approx. 10–15 % smaller. | The viscosity drops to a third, Re increases, λ decreases slightly. The effect is smaller than you might think – unlike with viscous media such as oil. |
| Add ten 90° elbows | The local losses make up a noticeable share, in short lines often more than the straight pipe. | Each bend costs ζ · ρ v²/2. In plant rooms with many fittings, valves and bends make up the main share. |
| Swap steel for plastic pipe (PE) | λ becomes smaller, Δp drops – but the inside diameter is smaller with PE. | A smooth wall causes less friction, the thick plastic wall costs cross-section. Both together decide. |
Typical mistakes
- Calculating with DN instead of the inside diameter – with thick-walled pipes, you end up way off.
- Mixing up units: m³/h and l/s (factor 3.6), bar and m water column (factor ≈ 10.2).
- Using the design temperature of the piping spec as the operating temperature – for the flow, the operating temperature is what counts.
- Calculating gas with constant density even though the pressure drops considerably along the line (more than 10%).
For practice
Exercise: water at 20 °C, 36 m³/h, steel pipe DN 100 (114.3 × 3.6 mm), 100 m straight line. What are the velocity, Reynolds number and pressure drop? Is a pump with 2 m head sufficient for the friction?
Show solution
di = 114.3 − 2 · 3.6 = 107.1 mm; A = π/4 · 0.1071² = 0.00901 m²; Q = 36 m³/h = 0.01 m³/s → v = 0.01 / 0.00901 ≈ 1.11 m/s. Re = 1.11 · 0.1071 / 1.0·10⁻⁶ ≈ 119,000 → turbulent. With k = 0.05 mm, Colebrook-White gives λ ≈ 0.020. Δp = 0.020 · 100 / 0.1071 · 998 · 1.11² / 2 ≈ 11,300 Pa ≈ 0.11 bar ≈ 1.15 m. Yes, 2 m is enough for the friction – but bends, valves and difference in elevation come on top. Reproduce it in the calculator: series "Steel pipe", 36 m³/h, length 100 m, no fittings.
For training and studies: this page may be shown in class. Property values are guide values; for verification, the standards and manufacturer data apply.
What is the calculator for?
Why you need it
The nominal size determines the cost and operation of a line: pipe, valves, insulation and supports get more expensive with every DN step, while an undersized line costs pump energy permanently, becomes noisy and wears out. The pressure drop is the head a pump has to deliver.
Which tasks it solves
- What nominal size does the line need for a given flow rate?
- How high is the pressure drop to the consumer – is the pump sufficient?
- Which of the two routing variants has less loss?
- After modeling: does the DN still match the actual routing?
When in the design process
- Basics / preliminary designLine list: DN per line from the flow rate
- Basic engineeringPump head for the pump enquiry, compare routing variants
- Detail engineeringCheck with actual length and fittings from the 3D model (PCF)
- Installation / commissioning–
- Operation / modification of existing plantsIs the existing line sufficient for a higher flow rate?
Frequently asked questions
Which pipe series should I use?
The series of your piping spec – the wall thickness determines the inside diameter. For your own wall thicknesses, size the class in the Piping Spec Calculator first.
Does the calculator also size pumps?
It provides the pressure drop of the system as head (m). Pump curve and NPSHNPSH – Net Positive Suction Head Pressure margin at the pump inlet above the vapour pressure of the fluid. The system must provide more NPSH (NPSHa) than the pump requires (NPSHr), otherwise cavitation occurs. Background and sources › belong in the pump selection.
Terms, background and sources 21 terms on this page
Brief explanations for reference. They do not replace the standard or code itself.
- DN – Nominal size (DN)
Designation for the size of pipes, fittings and valves (Diameter Nominal). It is roughly the inside diameter in millimeters but is not an exact dimension.
Specified in DIN EN ISO 6708. Which outside diameter belongs to a DN is defined in the dimensional standards, e.g. DIN EN 10220 for steel pipes.
- EN – European Standard
European Standard, developed by CEN (general) or CENELEC (electrical engineering).
Every member country must adopt an EN unchanged as a national standard – in Germany as “DIN EN …”. Conflicting national standards are withdrawn.
- ASME – American Society of Mechanical Engineers
US engineering society. Its codes for piping, flanges and pipe dimensions apply in many plants worldwide.
ASME was founded in 1880. Well-known codes: B31.3 (process piping), B16.5 (flanges), B36.10M and B36.19M (pipe dimensions).
- PE – Polyethylene
Polyethylene, a thermoplastic for gas, water and wastewater pipes. “PE 100” indicates the strength class (MRS 10 MPa).
Abbreviations for plastics according to DIN EN ISO 1043-1.
- DIN 11850 – Stainless steel tubes for the food and chemical industry – Dimensions, materials
Specifies outside diameters, wall thicknesses (series 1 to 3) and materials of stainless steel tubes for food, chemical and pharmaceutical plants. In the Piping Spec Calculator, “DIN 11850 series 2” is the usual hygienic tube series.
The pipes are usually orbital welded; detachable joints follow DIN 11851 (union) or DIN 32676 (clamp), aseptic joints DIN 11864.
- PCF – Piping Component File
Text file with which AutoCAD Plant 3D passes piping data to the isometric generator and to other programs.
- DIN EN 10220 – Seamless and welded steel tubes – General tables of dimensions and masses per unit length
The basic table of outside diameters and wall thicknesses of steel pipes (series 1 to 3). The Piping Spec Calculator takes the outside diameter per DN from it (series 1), e.g. 114.3 mm for DN 100.
Replaces the former DIN 2448 and DIN 2458; the prestandard was called DIN V ENV 10220. Current edition 2003-03 (DIN Media).
- PDF – Portable Document Format
File format for documents that looks the same on every device and can be printed – e.g. the piping class sheet.
- DIN EN ISO 1127 – Stainless steel tubes – Dimensions, tolerances and conventional masses per unit length
Dimension and tolerance standard for stainless steel pipes: outside diameters, wall thicknesses and the tolerance classes D and T. In the Piping Spec Calculator, the minus tolerance of the wall thickness for stainless steel is based on it.
- B36.10M – ASME B36.10M Steel Pipe
US dimensional standard for welded and seamless steel pipes: outside diameters and wall thicknesses (schedule).
- B36.19 – ASME B36.19
US dimensional standard for stainless steel pipe: outside diameters and wall thicknesses (schedule with “S”, e.g. 10S).
- TU – Technical university
Technical university (Technische Universität), e.g. TU Graz.
- VDI – Association of German Engineers
Association of German Engineers. Its VDI guidelines are regarded as generally accepted rules of technology.
- VG – Viscosity grade
Viscosity grade for oils according to ISO 3448: the number is the mean kinematic viscosity at 40 °C in mm²/s, e.g. ISO VG 46.
- KSB
Maker of pumps and valves; its centrifugal pump handbook is a widely used source of flow data.
- DIN 2448 – Seamless steel tubes – Dimensions, masses per unit length
Former German dimension standard for seamless steel pipes, withdrawn and replaced by DIN EN 10220. The outside diameters of series 1 have largely remained the same; wall thicknesses of old pipe specs often still come from DIN 2448.
- DIN 2458 – Welded steel tubes – Dimensions, masses per unit length
Former German dimension standard for welded steel pipes, withdrawn and, like DIN 2448, replaced by DIN EN 10220.
- ISO – International Organization for Standardization
International Organization for Standardization in Geneva: it develops standards that apply worldwide (ISO standards).
ISO was founded in 1947. Its members are the national standards bodies; for Germany, this is DIN.
- IEC – International Electrotechnical Commission
International Electrotechnical Commission in Geneva: worldwide standards for electrical engineering and for instrumentation and control.
IEC was founded in 1906. IEC standards adopted in Europe are called “EN IEC …” or “EN 6xxxx”.
- bar – Unit of pressure
Unit of pressure: 1 bar = 100,000 Pa = 0.1 MPa. In plant engineering, it usually refers to the gauge pressure relative to the surroundings (often “barg” or, in German, “bar ü”).
- NPSH – Net Positive Suction Head
Pressure margin at the pump inlet above the vapour pressure of the fluid. The system must provide more NPSH (NPSHa) than the pump requires (NPSHr), otherwise cavitation occurs.
Sources and origins
- ISO 6708 – Pipework components, definition and selection of DN (for DN)
- DIN – German Institute for Standardization (for DN)
- CEN and CENELEC – European standardization (for EN)
- ASME – American Society of Mechanical Engineers (for ASME, B36.10M)
- ISO – International Organization for Standardization (for PE, VG, ISO)
- DIN Media: DIN 11850 (for DIN 11850)
- Autodesk – AutoCAD Plant 3D Help (for PCF)
- DIN Media: DIN EN 10220:2003-03 (for DIN EN 10220, DIN 2448)
- Wikipedia: Portable Document Format (German) (for PDF)
- DIN Media: DIN EN ISO 1127:2019-03 (for DIN EN ISO 1127)
- ASME (for B36.19)
- Graz University of Technology (for TU)
- VDI – Association of German Engineers (for VDI)
- KSB (for KSB, NPSH)
- DIN Media: DIN 2448 (withdrawn) (for DIN 2448)
- DIN Media: DIN 2458 (withdrawn) (for DIN 2458)
- IEC – International Electrotechnical Commission (for IEC)
- BIPM – International System of Units (SI) (for bar)