Skip to main content
Software und Anwendung für AutoCAD Plant 3D · Autodesk Authorized Training Center · Frankfurt am Main Deutsch · Español · +49 69 9450725-0 · vertrieb@seitz-ingenieure.de

Free · Calculator 7

Thermal expansion and expansion compensation

Change in length between anchor points from installation, minimum and maximum temperature, compensator with pre-tension and a first estimate for L-, Z- and U-bends.

The task

Fast, traceable answers in piping design.

What you want

  • You want all small calculations in one place.
  • You want to follow every calculation step.

Our solution

  • Free calculators in the browser: size and pressure drop, thermal expansion, weight, converter, tagging.
  • Formulas, values and the governing criterion visible.

Your advantage

  • Answers in seconds.
  • Traceable in discussions.
  • No installation, no login.
  • Guide values with source – preliminary sizing.

Loading calculator …

Preliminary sizing, not a piping design. Dimensions and material properties come from the ASEING Piping Spec Calculator and Support Span Calculator and are estimates from publicly available manufacturer data, generalized; all other values are guide values. They may deviate from the standard – check against the applicable standards and manufacturer data before binding use. You can enter your own values in the calculator.

Basics, calculation method, examples and FAQ ▸

Basis & sources

What the tool calculates with, which standards and data it relies on and where its limits are. As of September 2026. For practice: Understand it and try it out.

Estimated values: dimensions, material properties, ratings and product ranges are generalized estimates from publicly available manufacturer data. They may deviate from the respective standard in individual points. The current standard and your manufacturer's data are binding. You can load your own values – e.g. from your standard – directly in the tool; they stay on your computer and are not transferred to us.
Calculation method
  1. ExpansionΔL = α·L·ΔT with mean coefficient of thermal expansion from 20 °C
  2. Expansion jointtotal movement + 10 % (ASEING guide value), pre-set to mid-position
  3. Flexible legmetal: guided cantilever L = √(3·E·D·δ / σ) with E at 20 °C; plastic: L = C·√(D·δ) according to manufacturer documentation
  4. NextPlan support spans and supports
Standards & codes

Reference: the calculation is based on these standards and codes. Standard texts and tables are not included.

DIN EN 13480-3DIN EN 13480 – Metallic industrial piping The European standard for metallic industrial piping: part 2 materials, part 3 design and calculation, part 4 fabrication, part 5 inspection and testing. The Piping Spec Calculator sizes wall thicknesses according to part 3 – as a preliminary sizing, not a piping design. Background and sources ›, ASME B31.3B31.3 – ASME B31.3 Process Piping US code for process piping: materials, design, fabrication and testing of piping in chemical and process plants. Background and sources ›Stress verification in the pipe stress analysis (not part of the calculator)
DIN EN 13445-3DIN EN 13445 – Unfired pressure vessels The European standard for unfired pressure vessels; part 3 covers design and calculation. For piping, DIN EN 13480 applies instead. Background and sources ›, Annex OModulus of elasticity over temperature as in the Support Span Calculator
Data & origin
Coefficients of thermal expansion αMaterial data sheets (Swiss Steel, thyssenkrupp, Aurubis) and manufacturer documentation (GF, Sikla) – source per material in the table in the calculator (“where does α come from?”); for ranges, the value with the greater expansion
Flexible leg constant, plasticSikla, Chapter 18 Piping technology (according to DVS 2210-1DVS 2210 – Industrial piping made of thermoplastics – Design and execution Guideline for above-ground plastic pipelines: installation, support spacing and compensation of expansion. The expansion calculator takes from it the approach for the bending leg length L = C · √(D·δ). Background and sources ›)
Allowable bending stress, metalASEING guide value, adjustable in the calculator
Assumptions & limits
  • Estimate of whether a bend fits – not a pipe stress analysis (anchor forces, support friction, stress verification).
  • Values outside the range of validity of α are flagged ("Not usable as is").
  • Plastic: expansion about 10 to 15 times that of steel, modulus of elasticity time-dependent – observe the manufacturer data.
Standards status for this page 2 standards · researched October 2026
StandardContentsCurrent editionReplaced / successor
DIN EN 13480-3Metallic industrial piping – Part 3: Design and calculationDIN EN 13480-3:2024-12replaces DIN EN 13480-3:2017-12; DIN EN 13480-3/A1A1, A2 … – Amendment of a standard Amendment of a standard. It is followed by the year of issue, e.g. A2:2019 = second amendment, published in 2019. The standard and its amendments apply together. Background and sources ›:2021-05; DIN EN 13480-3/A2:2020-12
ASME B31.3Process PipingASME B31.3-2024replaces ASME B31.3-2022

Researched at DIN Media, ISOISO – International Organization for Standardization International Organization for Standardization in Geneva: it develops standards that apply worldwide (ISO standards). Background and sources ›, IECIEC – International Electrotechnical Commission International Electrotechnical Commission in Geneva: worldwide standards for electrical engineering and for instrumentation and control. Background and sources › and ASMEASME – American Society of Mechanical Engineers US engineering society. Its codes for piping, flanges and pipe dimensions apply in many plants worldwide. Background and sources ›, as of October 2026. Before binding use, please check the current edition with the standards publisher. Overview of all standards: Plant Engineering Infobase · Standards status.

Understand it and try it out

Metal and plastic get longer when they heat up. A few millimeters per meter sounds harmless – over a 40 m line it quickly adds up to 8 cm, and that has to go somewhere. Here you can see how much it is and how to absorb it.

The terms in five minutes

Coefficient of thermal expansion α
How much longer a material gets per kelvin, e.g. steel around 12 · 10⁻⁶/K: 1 m gets 1.2 mm longer when heated by 100 K. Plastics expand 10 to 15 times as much.
Change in length ΔL
ΔL = α · L · ΔT. Double the length or double the temperature difference → double the expansion.
Anchor point
Holds the line in place at one point. Between two anchor points, the expansion must be absorbed.
Sliding and guide supports
Carry the pipe but let it move longitudinally (sliding support) or only in one direction (guide).
Compensator
A bellows that absorbs the movement. Axial compensators absorb longitudinal movement but need anchor points that take up the internal pressure.
Expansion leg / U-loop
A transverse pipe section that bends elastically – the "natural" compensation without bellows. Needs space.
Pre-tension
The compensator is installed slightly stretched or compressed at installation temperature so that it works around its mid-position in operation.

Try it out and understand it

Change one value in the calculator above and watch what happens to the others:

Try itWhat happensWhy
Change the material from steel to PE 100PE – Polyethylene Polyethylene, a thermoplastic for gas, water and wastewater pipes. “PE 100” indicates the strength class (MRS 10 MPa). Background and sources › (same temperatures)The expansion becomes about 15 times as large.α of PE is about 180 · 10⁻⁶/K versus 12 · 10⁻⁶/K for steel. Plastic lines need much more expansion compensation – even with a small temperature range.
Set the installation temperature from 10 to 30 °CExpansion in operation decreases, contraction in winter increases – the pre-tension may change direction.What matters is the difference from the installation temperature, not the absolute temperature.
Double the pipe outside diameterThe required expansion leg becomes about 1.4 times as long.L ~ √D: thicker pipes are stiffer and need longer legs to absorb the same displacement without excessive stress.
Enter PVDFPVDF – Polyvinylidene fluoride Fluoroplastic with high chemical resistance, e.g. for acids and ultrapure water. Background and sources › at 600 °CThe calculator calculates but shows red: "Not usable as is".You can calculate anything – whether the material can withstand it is another question. Always check the operating range.

Typical mistakes

  • Considering only Tmax and forgetting the contraction at standstill – it pulls on nozzles and anchor points.
  • Installing the compensator without pre-tension – it then runs against its stop in operation.
  • Forgetting anchor forces: an axial compensator transfers the internal pressure as a force to the anchor points.
  • Treating plastic like steel: with plastics, the modulus of elasticity and allowable stress depend strongly on temperature and time.

For practice

Exercise: A 40 m steel line is installed at 10 °C and heated to 180 °C in operation. How much longer does it get? And roughly how long would an L-shaped expansion leg need to be for a 114.3 mm pipe?

Show solution

α (20 → 180 °C) ≈ 12.5 · 10⁻⁶/K; ΔL = 12.5·10⁻⁶ · 40,000 mm · 170 K ≈ 85 mm – i.e. roughly 8 to 9 cm. The flexible leg must absorb the entire movement between the coldest and the warmest state – at −10 °C in winter that is 84.5 + 9.2 = 93.7 mm. Flexible leg according to L = √(3 · E · D · δ / σ) with E = 212,000 N/mm²N/mm² – Newtons per square millimeter Unit of mechanical stress, e.g. yield strength or allowable stress: 1 N/mm² = 1 MPa. Background and sources › (at 20 °C, as is common in pipe stress analysis), D = 114.3 mm, δ = 93.7 mm, σ = 120 N/mm²: L ≈ √(3 · 212,000 · 114.3 · 93.7 / 120) ≈ 7.5 m. That is a lot of space – which is why long lines are divided by anchor points or U bends or expansion joints are installed. In the calculator: material steel, 40 m, 10 / −10 / 180 °C, outside diameter 114.3.

For training and studies: this page may be shown in class. Property values are guide values; for verification, the standards and manufacturer data apply.

What is the calculator for?

Why you need it

Pipelines get longer when heated – 40 m of steel pipe at 180 °C by around 8 cm. If the line cannot move freely, it pushes with large forces on anchor points and on the nozzles of pumps, vessels and heat exchangers: flanges leak, supports tear out, nozzles deform.

Which tasks it solves

  • How far does the line move between two anchor points?
  • Is the routing with its bends sufficient – or is a U-loop or compensator needed?
  • What movement capacity does the compensator need, and how far is it pre-tensioned during installation?
  • How much clearance do wall penetrations, pipe clamps and insulation need?

When in the design process

  1. Basics / preliminary design–
  2. Basic engineeringRouting and layout planning: provide space for bends, U-loops or compensators
  3. Detail engineeringDefine anchor points and sliding supports, check plausibility before pipe stress analysis
  4. Installation / commissioningInstall compensators with the correct pre-tension
  5. Operation / modification of existing plantsModification: can the new routing handle the temperature?

Frequently asked questions

Does this replace a pipe stress analysis?

No. The estimate shows whether a bend realistically fits. Anchor forces, support friction and stress verification per DIN EN 13480-3 or ASME B31.3 belong in the pipe stress analysis.

Why is plastic so critical?

Thermal expansion is about 10 to 15 times that of steel, the modulus of elasticity is low and time-dependent – design expansion legs and support spacing according to manufacturer data.

Terms, background and sources 12 terms on this page

Brief explanations for reference. They do not replace the standard or code itself.

PCF – Piping Component File

Text file with which AutoCAD Plant 3D passes piping data to the isometric generator and to other programs.

DIN EN 13480 – Metallic industrial piping

The European standard for metallic industrial piping: part 2 materials, part 3 design and calculation, part 4 fabrication, part 5 inspection and testing. The Piping Spec Calculator sizes wall thicknesses according to part 3 – as a preliminary sizing, not a piping design.

Current parts 1 to 6 and 8 in the 2024-12 edition; part 7 (conformity assessment) is a technical report, DIN CEN/TR 13480-7.

B31.3 – ASME B31.3 Process Piping

US code for process piping: materials, design, fabrication and testing of piping in chemical and process plants.

DIN EN 13445 – Unfired pressure vessels

The European standard for unfired pressure vessels; part 3 covers design and calculation. For piping, DIN EN 13480 applies instead.

DVS 2210 – Industrial piping made of thermoplastics – Design and execution

Guideline for above-ground plastic pipelines: installation, support spacing and compensation of expansion. The expansion calculator takes from it the approach for the bending leg length L = C · √(D·δ).

A1, A2 … – Amendment of a standard

Amendment of a standard. It is followed by the year of issue, e.g. A2:2019 = second amendment, published in 2019. The standard and its amendments apply together.

ISO – International Organization for Standardization

International Organization for Standardization in Geneva: it develops standards that apply worldwide (ISO standards).

ISO was founded in 1947. Its members are the national standards bodies; for Germany, this is DIN.

IEC – International Electrotechnical Commission

International Electrotechnical Commission in Geneva: worldwide standards for electrical engineering and for instrumentation and control.

IEC was founded in 1906. IEC standards adopted in Europe are called “EN IEC …” or “EN 6xxxx”.

ASME – American Society of Mechanical Engineers

US engineering society. Its codes for piping, flanges and pipe dimensions apply in many plants worldwide.

ASME was founded in 1880. Well-known codes: B31.3 (process piping), B16.5 (flanges), B36.10M and B36.19M (pipe dimensions).

PE – Polyethylene

Polyethylene, a thermoplastic for gas, water and wastewater pipes. “PE 100” indicates the strength class (MRS 10 MPa).

Abbreviations for plastics according to DIN EN ISO 1043-1.

PVDF – Polyvinylidene fluoride

Fluoroplastic with high chemical resistance, e.g. for acids and ultrapure water.

N/mm² – Newtons per square millimeter

Unit of mechanical stress, e.g. yield strength or allowable stress: 1 N/mm² = 1 MPa.

Sources and origins