Plant Engineering Infobase · Chapter 14 of 16
Standards status
Research status October 2026. The most recently determined edition is given. Check the current edition with the standards publisher before binding use. The standards compass sorts the rules by work step; the tables below show the status and the successors of withdrawn standards.
Standards compass: which rule for what – with reference to AutoCAD Plant 3D
The compass sorts the most important European rules by work step: legal framework, basic terms, P&IDR&I – Piping and instrumentation diagram Flow diagram showing all pipes, valves, equipment and instrumentation of a plant (P&ID, Piping and Instrumentation Diagram). Background and sources ›, annotation, piping specs, piping construction, industries and digital handover. For each rule it states what it applies to and where it takes effect in AutoCAD P&ID and Plant 3D. We do not reproduce standard texts or table values; the purchased current edition always governs.
Thinking European: An ENEN – European Standard European Standard, developed by CEN (general) or CENELEC (electrical engineering). Background and sources › standard applies in all CENCEN – European Committee for Standardization European Committee for Standardization in Brussels. It develops the European Standards (EN) outside electrical engineering. Background and sources › member countries with the same wording. Nationally it only appears with a different prefix – DINDIN – German Institute for Standardization German Institute for Standardization in Berlin: it publishes the German standards (DIN standards) and represents Germany in CEN and ISO. Background and sources › EN in Germany, ÖNORMÖNORM – Austrian standard Standard of Austrian Standards. “ÖNORM EN” is a European Standard adopted in Austria. Background and sources › EN in Austria, SNSN – Swiss standard Standard of the Swiss Association for Standardization SNV. “SN EN” is a European Standard adopted in Switzerland. Background and sources › EN in Switzerland, NEN-ENNEN – Dutch standard Standard of the Dutch standards body NEN. “NEN-EN” is a European Standard adopted in the Netherlands. Background and sources › in the Netherlands, BSBS – British Standard British standard of the standards body BSI. “BS EN” is a European Standard adopted in the United Kingdom. Background and sources › EN in the United Kingdom, NFNF – Norme française French standard of the standards body AFNOR. “NF EN” is a European Standard adopted in France. Background and sources › EN in France, UNE-ENUNE – Una Norma Española Spanish standard of the standards body UNE. “UNE-EN” is a European Standard adopted in Spain. Background and sources › in Spain. A project standard based on EN and EN ISOISO – International Organization for Standardization International Organization for Standardization in Geneva: it develops standards that apply worldwide (ISO standards). Background and sources › standards is therefore understood throughout Europe. Purely national rules (e.g. DIN 21057DIN 21057 – Piping specs for process plants Series of standards for structuring piping specs: part 1 fundamentals and naming, further parts per material. It is the successor of PAS 1057; ASEING piping specs are based on it. Background and sources ›, DIN 2403DIN 2403 – Identification of pipelines according to fluid conveyed DIN 2403 specifies how above-ground pipelines are marked according to the fluid they carry. Each fluid belongs to a group 0 to 9 with its own group colour; flammable and non-flammable gases, liquids and solids also carry an additional colour. “Gr.” with a number names the group, e.g. Gr. 1 = water, green. Background and sources ›, AD 2000AD 2000 – AD 2000 Code German code for pressure vessels: calculation, materials and manufacture. Working to it meets the requirements of the Pressure Equipment Directive. Background and sources ›, TRBSTRBS – Technical Rules for Operational Safety Technical rules for the German Ordinance on Industrial Safety and Health, e.g. on the inspection of pressure systems. Background and sources ›) are marked as such below; abroad, the national counterparts apply.
1 · Legal framework: what applies by law
EUEU – European Union European Union. Since the Treaty of Lisbon (end of 2009) the numbers of legal acts contain “EU”, e.g. Directive 2014/68/EU. Background and sources › directives and regulations define the protection goals. Harmonised standards (listed in the Official Journal of the EU) describe a way to reach them: whoever applies them may assume that the requirements are met (presumption of conformity). For pressure equipment, DIN EN 13480DIN EN 13480 – Metallic industrial piping The European standard for metallic industrial piping: part 2 materials, part 3 design and calculation, part 4 fabrication, part 5 inspection and testing. The Piping Spec Calculator sizes wall thicknesses according to part 3 – as a preliminary sizing, not a piping design. Background and sources › is such a standard.
| Rule | Used for | Significance for design in Plant 3D | Edition |
|---|---|---|---|
| Directive 2014/68/EU (PED) | Placing pressure equipment and assemblies on the market; classification by fluid group, pressure and nominal size | Carry fluid group and category per pipeline as a property of the line group – determined in the Piping Spec Calculator, evaluated in the P&ID and in the line list | 2014 |
| Directive 2014/34/EU (ATEXATEX – Directive 2014/34/EU Short name of EU Directive 2014/34/EU for equipment and protective systems in potentially explosive atmospheres (from French “ATmosphères EXplosibles”). Background and sources ›) | Equipment and protective systems for potentially explosive atmospheres | Carry explosion protection of instruments and drives as a property in the P&ID | 2014 |
| Directive 1999/92/EC | Protection of workers in explosive atmospheres; zone classification by the operating company | Ex zones as separate layers or area display in the 3D model and in the layout plan | 1999, consolidated 2007 |
| Directive 2006/42/EC → Regulation (EU) 2023/1230 | Machinery; the new Machinery Regulation applies essentially from 20.01.2027 directly in all EU countries | Concerns packages such as pump and dosing stations; mark interfaces and scope limits clearly in the P&ID | 2006 / 2023 |
| BetrSichV, TRBS 2141 (DE) | Operation and inspection of work equipment; hazards from steam and pressure | Make pipelines subject to inspection and inspection intervals evaluable via properties of the line group | 2015 · TRBS 2141 amended on an ongoing basis |
| AwSVAwSV – German ordinance on facilities handling substances hazardous to water (AwSV) German ordinance on how plants handling substances hazardous to water are built, operated and inspected. It also determines the water hazard class (WGK). Background and sources › (DE) | Installations handling substances hazardous to water: containment, double walls, leak detection | Water hazard class of the medium as a property; double-walled lines as a separate piping spec | 2017, amended 2020 |
| TATA Luft – Technical Instructions on Air Quality Control Administrative regulation under the German Federal Immission Control Act. It limits emissions from plants and sets requirements, e.g., for the tightness of flanged joints. Background and sources › Luft (DE) and VDI 2290VDI 2290 – Emission control – Characteristic values for tight flange connections Specifies the TA Luft (German Clean Air Regulations) requirements for “technically tight” flange connections: gasket selection, proof of tightness, assembly. Background and sources › | Emission reduction; technically tight flange connections | Choose gaskets and bolts in the piping spec accordingly (see section 5); the proof belongs to the flange calculation, not to CADCAD – Computer-Aided Design Computer-aided design and drafting. Background and sources › | TA Luft 2021 |
Examples (values for illustration; the current standard and the manufacturer data govern):
- Classification under the PED, compressed air (gas, fluid group 2): pipelines fall under the directive if DNDN – Nominal size (DN) Designation for the size of pipes, fittings and valves (Diameter Nominal). It is roughly the inside diameter in millimeters but is not an exact dimension. Background and sources › > 32 and PSPS – maximum allowable pressure Maximum allowable pressure according to the Pressure Equipment Directive, in bar gauge, set by the manufacturer. Together with the volume V or the nominal size DN it determines the category of the pressure equipment. Background and sources › · DN > 1000 barbar – Unit of pressure Unit of pressure: 1 bar = 100,000 Pa = 0.1 MPa. In plant engineering, it usually refers to the gauge pressure relative to the surroundings (often “barg” or, in German, “bar ü”). Background and sources › (Art. 4(1)(c)). PS 10 bar, DN 80 → PS · DN = 800 bar → not above, so sound engineering practice according to Art. 4(3), no CE marking. The same line in DN 150 → 1500 bar → within scope, category according to Annex II, table 7.
- Cooling water (liquid, fluid group 2): only from PS > 10 bar, DN > 200 and PS · DN > 5000 bar. PS 6 bar, DN 300 → Art. 4(3), even though the line is large.
- In Plant 3D: properties “fluid group” (1/2), “PS” and “PED category” on the line group; the line list filters all lines from category I upwards for documentation.
2 · Basic terms: DN, PN and pressure equipment terms
| Rule | Used for | In Plant 3D | Edition |
|---|---|---|---|
| DIN EN ISO 6708DIN EN ISO 6708 – Pipework components – Definition and selection of DN (nominal size) Defines the nominal size DN as a dimensionless reference number, not as a dimension. The actual outside diameter is in the catalog, e.g. DN 100 = 114.3 mm for steel pipe. Background and sources › | Nominal size DN: dimensionless reference value, not a dimension | Nominal size list of the piping spec (Spec Editor); never confuse DN and outside diameter – the catalog holds the real outside diameter | 1995-09 |
| DIN EN 1333DIN EN 1333 – Flanges and their joints – Pipework components – Definition and selection of PN Defines the nominal pressure PN as a reference number, not as the permissible pressure, and sets the PN series (PN 2.5 to PN 400). Which pressure is permissible at which temperature is stated in the product standard. Background and sources › | Nominal pressure PNPN – Nominal pressure rating Designation for the pressure rating of flanges and valves (Pressure Nominal), e.g. PN 16. It corresponds roughly to the allowable pressure in bar at room temperature; at higher temperatures, less is allowed. Background and sources ›: reference value for flanges and valves | Pressure rating as a component property; define the PN series of the piping spec | 2006-06 |
| DIN EN 764-1DIN EN 764 – Pressure equipment – Terminology Part 1 specifies the terms for pressure equipment: pressure, temperature, volume, nominal size. This way design and operating data have the same names everywhere in properties and lists. Background and sources › | Terms for pressure equipment (pressure, temperature, volume) | Consistent naming of calculation and operating data in properties and lists | 2016-12 |
| ISO 80000-1ISO 80000 – Quantities and units Part 1 covers how quantities and units are written, e.g. a space between number and unit. This way units are shown consistently in properties and labels. Background and sources › | Quantities and units, notation | Consistent units in properties and annotations (e.g. bar(g), °C, mm) | 2022 |
Examples (values for illustration; the current standard and the manufacturer data govern):
- DN is not a dimension: DN 100 has an outside diameter of 114.3 mm for steel pipe according to DIN EN 10220DIN EN 10220 – Seamless and welded steel tubes – General tables of dimensions and masses per unit length The basic table of outside diameters and wall thicknesses of steel pipes (series 1 to 3). The Piping Spec Calculator takes the outside diameter per DN from it (series 1), e.g. 114.3 mm for DN 100. Background and sources › (series 1), e.g. 108 mm for copper pipe according to DIN EN 1057DIN EN 1057 – Copper and copper alloys – Seamless round copper tubes for water and gas (sanitary and heating) Dimensions and tempers of copper tubes in building services, e.g. 108 × 2.5 mm instead of 114.3 mm for steel pipe. In the Piping Spec Calculator the temper (R220, R250, R290) determines the strength. Background and sources ›, and 110 mm for PEPE – Polyethylene Polyethylene, a thermoplastic for gas, water and wastewater pipes. “PE 100” indicates the strength class (MRS 10 MPa). Background and sources › pipe. In the Spec Editor, each nominal size therefore needs the outside diameter from the catalog.
- PN is not an allowable pressure at every temperature: a PN 16 flange withstands 16 bar only in the reference temperature range; with rising temperature the allowable pressure decreases depending on the material. The Piping Spec Calculator shows the pressure-temperature rating (based on Annex F/G of DIN EN 1092-1DIN EN 1092 – Flanges and their joints – Circular flanges, PN designated The flange standard by nominal pressure PN; part 1 covers steel flanges with types (e.g. type 11 weld neck flange), sealing faces (B1, C, D …) and dimensions. Annex G assigns the permissible pressure to the temperature for each material group. Background and sources ›).
- Units: 16 bar(g) corresponds to about 17 bar(abs); always state in properties whether gauge or absolute pressure is meant.
3 · P&ID and symbol libraries
| Rule | Used for | In AutoCAD P&ID | Edition |
|---|---|---|---|
| DIN EN ISO 10628-1DIN EN ISO 10628 – Diagrams for the chemical and petrochemical industry Part 1 specifies the kinds of flow diagrams (block, process, P&I diagram) and what each shows; part 2 the graphical symbols. Basis of the symbol library in AutoCAD P&ID. Background and sources › / -2 | Types of flow diagrams, minimum content, graphical symbols | Basis of the symbol library; create the project with symbol standard ISO or DIN, derive your own symbols from it | 2015-04 / 2013-04 |
| DIN 28000-4DIN 28000 – Chemical apparatus – Documentation in the life cycle of process plants Part 4 contains the graphical symbols for valves, pipelines and actuators in the flow diagram. It replaces DIN 2429 and complements DIN EN ISO 10628-2. Background and sources › (DE) | Symbols for piping components | Adds piping components to the library (successor of DIN 2429DIN 2429 – Graphical symbols for technical drawings – Pipelines Former symbol standard for pipelines and valves, withdrawn and replaced by DIN 28000-4. Background and sources ›) | 2014-07 |
| ISO 14617-1ISO 14617 – Graphical symbols for diagrams Series of standards for symbols in diagrams of all disciplines. Part 1 general rules; since 2025 the former parts 3 to 15 are combined in part 2. Background and sources › / -2 | Graphical symbols for diagrams; since 2025 part 2 consolidates the former parts 2 to 15 (incl. valves, measurement and control) | For comparing symbols in international projects; replace withdrawn parts in existing documents | 2025 / 2025 |
| ISO 15519-1ISO 15519 – Specification for diagrams for the process industry Part 1 covers general rules, part 2 measurement and control in diagrams of the process industry. Background and sources › / -2 | Rules for diagrams in the process industry; part 2 measurement and control | Design sheet layout, flow direction and references to continuation sheets consistently | 2010 / 2015 |
| DIN EN 62424DIN EN 62424 – Representation of process control engineering requests in P&I diagrams Specifies how instrumentation points are represented in the P&ID and designated with code letters (e.g. TIC = temperature, indication, control). It replaces DIN 19227-1; VDE classification VDE 0810-24. Background and sources › | Instrument loops in the flow diagram: code letters, presentation, data exchange (CAEXCAEX – Computer Aided Engineering Exchange XML format according to IEC 62424 for exchanging design data, e.g. instrumentation loops, between programs. Background and sources ›) | Set up instrument classes and the tag format of the instrument loops accordingly; signal lines as a separate line class | 2017-12 |
| ANSI/ISA-5.1ANSI/ISA-5.1 – Instrumentation and Control – Symbols and Identification US counterpart to DIN EN 62424: symbols and code letters for instruments in flow diagrams (e.g. FIC, PT). AutoCAD P&ID has its own ISA symbol library for it; do not mix with DIN EN 62424. Background and sources › (USUS – United States United States of America. Background and sources ›) | Instrument symbols in the US | Use the ISAISA – International Society of Automation US association for automation. Its standard ISA-5.1 specifies symbols and identification letters for instrumentation. Background and sources › symbol standard only if the client requires it – do not mix with DIN EN 62424 | 2024 |
| IEC 60617IEC 60617 – Graphical symbols for diagrams (database) The database of graphical symbols for electrical engineering. Used in the P&ID for electrical symbols such as motor or heater. Background and sources › | Graphical symbols for electrical diagrams (database) | For electrical and drive symbols that appear in the P&ID (motor, heater) | Database, ongoing |
| DIN EN 61511-1DIN EN 61511 – Functional safety – Safety instrumented systems for the process industry sector Application of functional safety in the process industry: safety functions are designed for a target SIL. In the P&ID such control points must be marked recognisably. Background and sources › | Functional safety of safety instrumented systems in the process industry (SILSIL – Safety Integrity Level Safety level 1 to 4 for safety functions according to IEC 61508 and IEC 61511 – the higher the level, the less often the safety function may fail. Background and sources ›) | Mark safety-related instrument loops recognisably in the P&ID target SIL as a property of the loop | 2019-02 |
| DIN EN 61508-1DIN EN 61508 – Functional safety of electrical/electronic/programmable electronic safety-related systems Basic standard of functional safety for devices and manufacturers (SIL 1 to 4). In the P&ID it only appears as a property, e.g. the SIL capability of a device. Background and sources › | Basic standard for functional safety of devices | Manufacturer certificates of the devices; in the P&ID only as a property (SIL capability) | 2011-02 |
Practice: One symbol library per company, derived from a symbol standard, with fixed layers and tag formats. If a client deviates, create the project with the client's standard – do not convert it afterwards. How this is set up in AutoCAD P&ID is shown in chapter 12.
Examples (values for illustration; the current standard and the manufacturer data govern):
- Instrument loop according to DIN EN 62424: “PIC 101” = pressure (P), indication (I), control (C), loop 101; “TIR 201” = temperature, indication, recording. In the tag format: code letters and number as separate properties so that instrument lists remain sortable.
- Safety-related loop: a shutdown on overpressure with target SIL 2 is marked as a safety function in the P&ID and gets the property “SIL = 2” – the assessment itself belongs in the safety study, not in CAD.
- Symbol standard: create the project for a German client with the DIN/ISO symbol standard; for a US client with ISA – mixing both in one project leads to duplicate classes.
4 · Annotation, identification and title blocks
| Rule | Used for | In Plant 3D | Edition |
|---|---|---|---|
| DIN EN ISO 7200DIN EN ISO 7200 – Technical product documentation – Data fields in title blocks and document headers Specifies the data fields of the title block, including seven mandatory fields such as identification number, title, creator and date of issue. Width 180 mm, position bottom right. Background and sources › | Data fields in title blocks and document metadata | Link the title block to project and drawing properties – one title block for P&ID, ortho and iso | 2004-05 |
| DIN EN ISO 5457DIN EN ISO 5457 – Technical product documentation – Sizes and layout of drawing sheets Covers sheet sizes, frames (20 mm filing margin on the left, 10 mm elsewhere), grid zones and folding marks of drawing sheets. Background and sources › | Sheet formats, frames, folding marks | Template DWGDWG – AutoCAD drawing format AutoCAD file format for drawings and 3D models; AutoCAD Plant 3D and AutoCAD P&ID also save in this format. Background and sources › per format (A0A0 … A4 – Paper sizes Paper sizes according to DIN EN ISO 216: A4 = 210 × 297 mm. Each smaller number doubles the area (A3 = 297 × 420 mm, A0 = about 1 m²). Background and sources ›–A3); iso usually A3 | 2017-10 |
| DIN EN ISO 3098-1DIN EN ISO 3098 – Technical product documentation – Lettering Covers standard lettering in drawings: lettering types A and B, character heights from 2.5 mm. Background and sources › | Lettering for technical drawings | Text styles of the templates with fixed text heights | 2015-06 |
| DIN EN ISO 128-1DIN EN ISO 128 – Technical product documentation – General principles of representation Series of standards for representation in drawings; part 2 covers the line types (continuous, dashed, dash-dot line) and replaces DIN ISO 128-24. Background and sources › / -2 | Basic rules of presentation, line types and widths | Line types and lineweights per layer or plot style | 2022-02 / 2023-06 |
| DIN ISO 5455DIN ISO 5455 – Technical drawings – Scales Specifies the recommended scales, e.g. 1:2, 1:5, 1:10 and their multiples of ten, as well as enlargements 2:1, 5:1. Background and sources › | Scales | Ortho views in standard scales (1:20, 1:25, 1:50 …) | – |
| DIN EN ISO 13567-1DIN EN ISO 13567 – Technical product documentation – Organization and naming of layers for CAD Part 1 covers a key for layer names (responsible party, element, presentation). Useful when layers are coordinated with construction or building services. Background and sources › | Structure and naming of CAD layers | Define the layer scheme for model, ortho and iso; assign layers automatically via classes or component types | 2018-02 |
| DIN EN IEC 81346-1DIN EN IEC 81346 – Industrial systems – Structuring principles and reference designations The cross-industry basis of plant designation: each object under three aspects – function (=), product (-) and location (+). Part 2 contains the code letters, ISO/TS 81346-10 the version for power plants (RDS-PP). Background and sources › / -2 | Structuring and reference designation (=function, -product, +location) | Tag formats with prefixes and separators; split identifiers into properties, not as free text | 2024-07 / 2020-10 |
| VGB-S-811-01 (KKSKKS – Power plant identification system Identification of plants, systems, equipment units and components in power plants according to guideline VGB-S-811-01. Background and sources ›), VGB-S-823 (RDS-PPRDS-PP – Reference Designation System for Power Plants Identification system for power plants based on the international standard series ISO/IEC 81346; successor to KKS. Background and sources ›) | Identification in power plants and energy systems | Separate tag formats per identification system; check the number of characters in the format | 2018 / 2015 |
| DIN 2403 (DE), DIN EN ISO 7010DIN EN ISO 7010 – Graphical symbols – Safety colours and safety signs – Registered safety signs The collection of warning, prohibition, mandatory and safe condition signs. Together with DIN 2403 it determines the signs on pipelines. Background and sources › | Marking of pipelines by fluid; safety signs | Fluid group as a property – derive colours in the model and sign lists from it | 2025-12 / 2020-07 |
Line designation: There is no standard for the structure of the line number. Common practice is line number – DN – medium – piping spec – insulation. What matters is that each element is a property of its own and the tag format only combines them; then lists, iso title block and the P&ID ↔ 3D comparison stay consistent.
Examples (values for illustration; the current standard and the manufacturer data govern):
- Line number from properties: “1001-DN100-W-10CA01B1-H50” = number 1001, DN 100, medium water, piping spec 10CA01B1, heat insulation 50 mm. The tag format only combines them; each item remains individually evaluable.
- Reference designation according to DIN EN IEC 81346: “=A1.P001 -MA1 +B2” = function pump station 1, product motor, location building B2. KKS example: “1LAB10 AP001” = unit 1, feedwater system LAB 10, pump AP 001.
- Sheet and lettering: isometric A3 (297 × 420 mm), layout A1 (594 × 841 mm); text heights in the series 2.5 – 3.5 – 5 – 7 mm; line widths in a ratio of 1 : 2, e.g. 0.25 / 0.5 mm; ortho at scale 1:25 or 1:50.
5 · Piping specs: components, materials, connections
| Rule | Used for | In Plant 3D (Spec Editor, catalog) | Edition |
|---|---|---|---|
| DIN 21057-1 (DE) | Principles for creating piping specs | Structure and naming of piping specs, content of the piping spec sheet | 2023-08 |
| DIN EN 13480-2 / -3 | Materials; calculation of wall thicknesses | Wall thickness per DN in the piping spec (preliminary sizing in the Piping Spec Calculator) | 2024-12 |
| DIN EN 10216DIN EN 10216 – Seamless steel tubes for pressure purposes – Technical delivery conditions Series of standards for seamless pressure pipes: part 1 non-alloy steels at room temperature, part 2 steels for elevated temperatures (e.g. P235GH), part 5 stainless steels. It provides the strength values the Piping Spec Calculator uses for the preliminary sizing of the wall thickness. Background and sources › / 10217, DIN EN 10220 | Seamless or welded tubes; dimensions | Pipe catalog: outside diameter, wall thickness, material and order text | see table above |
| DIN EN 10253DIN EN 10253 – Butt-welding fittings Series of standards for butt-welding elbows, tees, reducers and caps; part 2 for non-alloy and ferritic steels, part 4 for austenitic steels. In the piping spec, fittings usually refer to part 2 or 4. Background and sources › | Butt-welding fittings | Elbows, tees, reducers, caps in the catalog | see table above |
| DIN EN 1092-1, DIN EN 1514DIN EN 1514 – Flanges and their joints – Dimensions of gaskets for PN-designated flanges Dimension standard for flange gaskets: part 1 flat gaskets of non-metallic material, further parts spiral wound and kammprofile gaskets. The gasket thus fits the flange according to DIN EN 1092-1. Background and sources ›, DIN EN 1515DIN EN 1515 – Flanges and their joints – Bolting Covers selection (part 1) and material combinations (part 2) of bolts and nuts for flange connections, e.g. 25CrMo4 at higher temperatures. Background and sources ›, DIN EN 13555DIN EN 13555 – Flanges and their joints – Gasket parameters and test procedures Specifies how gasket parameters (e.g. minimum surface pressure, creep relaxation) are measured. The flange calculation according to DIN EN 1591-1 needs these values. Background and sources › | Flanges, gaskets, bolts, gasket parameters | Flanges with facing type, matching gasket and bolt set per PN; bolt lengths from the catalog | 13555:2021-04 |
| DIN EN 736-1DIN EN 736 – Industrial valves – Terminology Part 1 defines the basic types (globe valve, gate valve, plug valve, butterfly valve), further parts terms and nominal sizes. This way valves are named consistently in the catalog. Background and sources ›, DIN EN 19DIN EN 19 – Industrial valves – Marking of metallic valves Specifies what must be marked on a valve: nominal size, nominal pressure, material, manufacturer, flow direction. Background and sources › | Valves: terms of the basic types; marking on the body | Name valve types unambiguously (class, long description) | 2018-05 / 2024-03 |
| DIN EN 1983DIN EN 1983 – Industrial valves – Steel ball valves Product standard for steel ball valves: designs, end connections, tests. In the valve catalog it is listed for the ball valves. Background and sources ›, 1984, 593, 13789, 12334 | Ball valves, gate valves, butterfly valves, globe valves, check valves | Valve catalog: face-to-face length, connection and pressure rating according to manufacturer data | 1983:2013-12 · 1984:2010-10 · 593:2018-01 (new edition 2026-11) · 13789:2010-09 · 12334:2004-10 |
| DIN EN ISO 4126-1DIN EN ISO 4126 – Safety devices for protection against excessive pressure Part 1 covers safety valves. Inlet and outlet nominal sizes are usually different – state them separately in the component and show the blow-off line in the P&ID. Background and sources › | Safety valves | Inlet and outlet nominal size separately in the component; show the discharge line in the P&ID | 2016-12 + A2:2019-08 |
| DIN EN 14917DIN EN 14917 – Metal bellows expansion joints for pressure applications Covers design, manufacture and testing of metal expansion joints. In Plant 3D they are a separate component class with installation length and pretension according to the manufacturer. Background and sources › | Metal expansion joints | Expansion joints as a separate component class; installation length and pre-stressing according to manufacturer | 2022-02 |
| DIN EN 10226-1DIN EN 10226 – Pipe threads where pressure-tight joints are made on the threads Taper external thread (R) with parallel or taper internal thread (Rp, Rc), sealing in the thread. Not to be confused with the parallel G thread according to DIN EN ISO 228. Background and sources ›, DIN EN ISO 228-1DIN EN ISO 228 – Pipe threads where pressure-tight joints are not made on the threads Parallel G thread; it does not seal in the thread but via a seal ring or flat gasket. Typical on valves and fittings. Background and sources ›, DIN EN 10255DIN EN 10255 – Non-alloy steel tubes suitable for welding and threading The classic threaded pipes (formerly DIN 2440/2441) in the medium and heavy series, for water, air and heating. They are threaded according to DIN EN 10226-1. Background and sources ›, DIN EN 10241DIN EN 10241 – Steel threaded pipe fittings Threaded steel fittings (sockets, nipples, elbows) for threaded pipes according to DIN EN 10255. Background and sources ›, DIN EN 10242DIN EN 10242 – Malleable cast iron threaded pipe fittings Malleable cast iron threaded fittings (the typical “building services fittings”). Design and pressure rating are indicated by code letters. Background and sources › | Pipe threads (sealing / non-sealing), threaded tubes, threaded fittings | Assign end types and connections for threads correctly (tapered ↔ parallel) | 2004-10 · 2003-05 · 2007-07 · 2000-08 · 2026-02 |
| DIN EN ISO 15494DIN EN ISO 15494 – Plastics piping systems for industrial applications – PB, PE, PE-RT, PE-X, PP Counterpart to DIN EN ISO 15493 for polyolefins. The Piping Spec Calculator uses it to calculate plastic pipes via the allowable stress σ = MRS/C and the SDR series. Background and sources ›, DIN EN ISO 15493DIN EN ISO 15493 – Plastics piping systems for industrial applications – ABS, PVC-U, PVC-C Requirements for pipes, fittings and valves made of ABS, PVC-U and PVC-C in industrial applications. Plastic pipe specs are built by SDR instead of wall thickness per DN. Background and sources ›, DIN EN 12201-2DIN EN 12201 – Plastics piping systems in PE for water supply Series of standards for PE pressure pipe systems in water supply; part 2 covers the pipes. For industrial PE piping, DIN EN ISO 15494 applies. Background and sources › | Industrial plastic piping; PE pipes for water | Plastic piping specs with SDRSDR – Standard Dimension Ratio Ratio of outside diameter to wall thickness for plastic pipes, e.g. SDR 11. A smaller SDR means a thicker wall and a higher allowable pressure. Background and sources › instead of wall thickness per DN; welded or bonded joints as end types | 15493:2017-07 · 12201-2:2025-03 |
Examples (values for illustration; the current standard and the manufacturer data govern):
- Calculation example wall thickness (preliminary sizing based on DIN EN 13480-3): e = p · Da / (2 · f · z + p). P235GHP235GH – Steel name for pressure equipment Steel designation according to DIN EN 10027-1: P = steel for pressure vessels and pressure pipes, number = minimum yield strength in MPa, letters = properties (e.g. GH for elevated temperatures, NL for low temperatures). Background and sources › at 20 °C with ReH = 235 MPaMPa – Megapascal Unit of pressure and mechanical stress: 1 MPa = 1 N/mm² = 10 bar. Background and sources › and Rm = 360 MPa → f = min(235/1.5; 360/2.4) = 150 MPa; p = 16 bar = 1.6 MPa, Da = 114.3 mm, seamless z = 1 → e = 1.6 · 114.3 / (300 + 1.6) ≈ 0.61 mm. Add corrosion allowance (e.g. 1 mm) and wall thickness tolerance; choose the next wall thickness of the dimension series, e.g. 3.6 mm. More in chapter 15.
- Flange designation: “Flange EN 1092-1/11/B1B1, B2 – Sealing face type according to DIN EN 1092-1 Shape of a flange sealing face: B1 = raised face (roughness Rz up to 50 µm), B2 = raised face, finer machined (Rz up to 12.5 µm). Background and sources ›/DN 100/PN 16/P250GH” = type 11 weld neck flange, facing B1, material P250GH. In the catalog this becomes the component, facing type (end type) and order text.
- Threads: external thread R ½ (tapered, DIN EN 10226-1) seals in internal thread Rp ½ (parallel); G ½ according to DIN EN ISO 228-1 does not seal in the thread but via a gasket. Create them as different end types in the Spec Editor, otherwise Plant 3D connects parts that do not fit together.
- Plastic: PE pipe d 110 SDR 11 → wall thickness e = d / SDR = 110 / 11 = 10 mm. The piping spec holds SDR per nominal size instead of a wall thickness table.
Background: formula symbols in the calculation example Barlow’s formula
| Symbol | Meaning – simply explained | Unit | Where does the value come from? |
|---|---|---|---|
| e | required wall thickness without allowances | mm | calculated |
| p | Design pressure; 16 bar = 1.6 MPa = 1.6 N/mm²N/mm² – Newtons per square millimeter Unit of mechanical stress, e.g. yield strength or allowable stress: 1 N/mm² = 1 MPa. Background and sources › | MPa | Input |
| Da | Outside diameter | mm | Dimensional standard |
| f | allowable stress | MPa | min(ReH/1.5; Rm/2.4) |
| z | Weld joint factor (seamless = 1) | – | Code |
| ReH, Rm | Yield strength and tensile strength from the tensile test | MPa | Material standard |
Derivation, origin and experiments: Chapter 15, Wall thickness (“Background” section).
6 · Design rules for piping construction and isometrics
| Rule | Used for | In Plant 3D | Edition |
|---|---|---|---|
| DIN EN 13480-3 / -4 / -5 | Supports and flexibility; fabrication and installation; inspection and testing | Support spacing as preliminary sizing (Support Span Calculator), test scope as a property of the line group | 2024-12 |
| ISO 6412-1ISO 6412 – Technical drawings – Simplified representation of pipelines Part 1 covers basic rules and orthogonal representation, part 2 isometric representation. The isometrics from AutoCAD Plant 3D follow these rules. Background and sources › / -2 | Simplified representation of pipelines; part 2 isometric projection | Iso style: symbols, dimensioning, welds, flow direction, slope | 2017 / 2017 |
| DIN EN ISO 3834-1DIN EN ISO 3834 – Quality requirements for fusion welding Specifies the quality requirements a welding company must meet (comprehensive, standard, elementary). Basis for fabricating piping according to DIN EN 13480. Background and sources ›, DIN EN ISO 9606-1DIN EN ISO 9606 – Qualification testing of welders – Fusion welding Covers welder qualification testing; part 1 for steel. Without a valid qualification, welding on pressure piping is not permitted. Background and sources ›, DIN EN ISO 15614-1DIN EN ISO 15614 – Specification and qualification of welding procedures – Welding procedure test Part 1 covers the procedure test for steel and nickel: a welding procedure is qualified on a test piece and then described in the WPS. Background and sources › | Quality in welding; qualification testing of welders; procedure qualification | Weld numbers on the iso, weld list from the model | 2022-01 · 2017-12 · 2020-05 |
| DIN EN ISO 5817DIN EN ISO 5817 – Welding – Quality levels for imperfections Specifies the quality levels B, C and D for welds (B = highest requirement). The required level is stated per piping spec. Background and sources ›, DIN EN ISO 17636-1DIN EN ISO 17636 – Non-destructive testing of welds – Radiographic testing Part 1 covers radiographic testing with film. Extent and testing class are specified in the weld list per piping spec. Background and sources › | Quality levels for welds; radiographic testing | Inspection class per piping spec; inspection scope in the weld list | 2023-07 · 2022-10 |
| DIN 4140DIN 4140 – Insulation work on industrial and building services installations Covers the execution and materials of thermal and cold insulation. In Plant 3D the insulation thickness affects clearances, support heights and clash detection. Background and sources › (DE), AGIAGI – Industrial construction association (Arbeitsgemeinschaft Industriebau) Arbeitsgemeinschaft Industriebau e. V. (industrial construction association). Its worksheets, e.g. AGI Q 101 on insulation work, are widely used design references in industry. Background and sources › Q 101, VDI 2055 Blatt 1VDI 2055 – Thermal and cold insulation of operational installations Part 1 covers the calculation of heat losses and insulation thicknesses. It complements DIN 4140, which covers the installation. Background and sources › | Insulation work; insulation in power plants; calculation of thermal and cold insulation | Insulation type and thickness as a property – affects clearances, support height and clash detection | 2023-05 · 2021-11 · 2025-10 |
| DIN EN ISO 12944-1DIN EN ISO 12944 – Corrosion protection of steel structures by protective paint systems Series of standards for paint systems: corrosivity categories C1 to CX and durability. The paint system is stated as a property of the pipeline. Background and sources › | Corrosion protection by coating | Coating system as a property of the line; colour in the model according to DIN 2403 | 2019-01 |
| DIN EN IEC 60079-10-1DIN EN IEC 60079-10 – Explosive atmospheres – Classification of areas Part 1 covers the classification of areas with explosive gas atmospheres into zones 0, 1 and 2. In Plant 3D the zones can be shown and checked as solids. Background and sources › | Classification of gas explosion hazardous areas into zones | Zones as solids in the model; clash detection with ignition sources in Navisworks | 2022-02 |
Design rules from practice (no standard values): minimum clearances for installation and insulation, slope towards drains, vents at high points, drains at low points, accessibility of valves, no flanges above walkways and control cabinets, safety valve discharge lines to atmosphere or into a collection system. These rules belong in the project design guideline; Plant 3D checks some of them via routing settings and clash detection.
Examples (values for illustration; the current standard and the manufacturer data govern):
- Insulation in the model: DN 100 (Ø 114.3 mm) with 50 mm insulation gives Ø 214.3 mm over the cladding – the clearance to the neighbouring line is based on the insulation diameter, not on the pipe. Plant 3D shows the insulation as a separate body and checks it in clash detection.
- Welds: steam piping spec with quality level B according to DIN EN ISO 5817 and 10 % radiographic testing → weld list from the model with a column “RT testing”, weld numbers on the isometric.
- Corrosion protection: outdoor line in an industrial atmosphere: corrosivity category C4, durability “high” according to DIN EN ISO 12944 – as the property “coating system” of the line, colour according to DIN 2403 (e.g. steam red, water green).
- Ex zone: zone 1 around a filling station as a solid in the model; Navisworks checks whether non-approved equipment is inside it.
7 · Industries with their own rules
| Industry | Rules | Effect on piping spec and model | Edition |
|---|---|---|---|
| Food, beverages, pharmaceuticals | Regulation (EC) 1935/2004, DIN EN 1672-2DIN EN 1672 – Food processing machinery – Hygiene requirements Part 2 specifies how machines and plants for food must be designed hygienically: cleanable surfaces, no dead spaces, drainability. For the piping spec this means connections without dead space and a defined surface finish. Background and sources ›, EHEDGEHEDG – European Hygienic Engineering & Design Group European professional association with guidelines for hygienic design in food and pharmaceutical plants. Background and sources › Guideline 8 | Dead-space-free connections (DIN 11850DIN 11850 – Stainless steel tubes for the food and chemical industry – Dimensions, materials Specifies outside diameters, wall thicknesses (series 1 to 3) and materials of stainless steel tubes for food, chemical and pharmaceutical plants. In the Piping Spec Calculator, “DIN 11850 series 2” is the usual hygienic tube series. Background and sources ›/11851/32676/11864), slope and drainability, surface finish as a property | 2004 (2021) · 2021-05 · 2025-12 |
| Gas | DIN EN 1775DIN EN 1775 – Gas supply – Gas pipework for buildings Covers gas pipework in buildings up to 5 bar. In Germany DVGW-TRGI and DVGW G 459 supplement the standard. Background and sources ›, DVGW G 459-1DVGW G 459 – DVGW worksheet G 459 – Gas service connections Part 1 covers planning and construction of gas service connections up to the main shut-off device. Decisive for gas piping specs and shut-offs in the connection area. Background and sources › (DE), DIN EN 12007DIN EN 12007 – Gas infrastructure – Pipelines for maximum operating pressure up to and including 16 bar Series of standards for public gas supply pipelines; part 1 general requirements, part 3 steel pipelines. It replaces the former DIN 2470. Background and sources › | Separate gas piping specs; shut-offs and marking | 2007-10 · 2026-07 |
| District heating | DIN EN 253DIN EN 253 – District heating pipes – Bonded single pipe systems with plastic casing Covers district heating bonded pipes: steel service pipe, PUR insulation, PE casing. That is why the catalog also lists the casing outside diameter. Background and sources ›, DIN EN 13941-1DIN EN 13941 – District heating pipes – Design and installation of bonded pipe systems Part 1 covers design, structural analysis and installation of buried district heating pipelines made of bonded pipes, including compensation of expansion. Background and sources › | Pre-insulated bonded pipes with casing outside diameter in the catalog; expansion compensation | 2024-10 · 2022-06 |
| Drinking water | DIN EN 806-1DIN EN 806 – Specifications for installations inside buildings conveying water for human consumption Series of standards for drinking water installations inside buildings: planning, sizing, installation and operation. In Germany DIN 1988 supplements the series. Background and sources ›, DIN 1988-100DIN 1988 – Codes of practice for drinking water installations (national supplement) German supplement to DIN EN 806; part 100 covers the protection of drinking water and the choice of materials. Background and sources › (DE) | Materials suitable for drinking water; protective devices in the P&ID | 2001-12 · 2011-08 |
| Refrigeration and heat pumps | DIN EN 378-1DIN EN 378 – Refrigerating systems and heat pumps – Safety and environmental requirements Part 1 covers basic requirements and divides refrigerants into safety groups (e.g. A1, A2L, B2L). The refrigerant is thus treated like a fluid of the piping spec. Background and sources › | Refrigerant as a medium with safety group; copper in inch sizes (see piping specs) | 2021-06 |
| Power plant | VGB-S-811-01 (KKS), ISO 81346-10 (RDS-PP), AGI Q 101 | Identification system in the tag format, insulation according to AGI | 2018 · 2022 · 2021-11 |
| Flue gas systems | DIN EN 1443DIN EN 1443 – Chimney systems – General requirements Basic standard for chimneys: classification by temperature, pressure, condensate resistance and corrosion. Flue gas lines usually do not fall under the Pressure Equipment Directive. Background and sources ›, DIN EN 1856DIN EN 1856 – Chimney systems – Requirements for metal chimneys Part 1 covers metal system chimneys, part 2 flue liners and connecting flue pipes. It applies together with DIN EN 1443. Background and sources › | See Piping specs, flue gas example | – |
Examples (values for illustration; the current standard and the manufacturer data govern):
- Hygiene: product line with slope for draining (e.g. 1 %), connections according to DIN 11864DIN 11864 – Stainless steel valves for aseptic, chemical and pharmaceutical applications Series of standards for aseptic connections with minimal dead space: part 1 unions, further parts flange and clamp connections. It is chosen when work is sterile and DIN 11851 or DIN 32676 are not sufficient. Background and sources › instead of standard flanges with flat gaskets, internal surface finish e.g. Ra ≤ 0.8 µm as a property of the piping spec.
- District heating: pre-insulated bonded pipe DN 100 with casing Ø 225 mm (insulation series 2 depending on the manufacturer) – store the casing outside diameter in the catalog, otherwise clearances and trench width are wrong.
- Refrigeration: copper pipe in inch sizes, e.g. Ø 22.22 mm (⅞″) → DN 20 in the piping spec according to the nearest metric pipe, inch size in the description.
8 · Digital handover, documentation and data exchange
| Rule | Used for | In Plant 3D | Edition |
|---|---|---|---|
| DIN EN ISO 19650-1DIN EN ISO 19650 – Information management using BIM Part 1 specifies the terms and principles of information management: roles, processes and the common data environment (CDE), e.g. Autodesk Docs. Background and sources › | Information management using BIMBIM – Building Information Modeling Planning, building and operating with a digital model that contains not only the geometry but also the properties of the components. Background and sources ›: terms, roles, processes | Common data environment (e.g. Autodesk Construction Cloud), status and approval of files | 2019-08 |
| DIN EN ISO 16739-1DIN EN ISO 16739 – Industry Foundation Classes (IFC) for data sharing in the construction and facility management industries The open data format IFC (currently IFC 4.3) for exchange with construction and building services. Background and sources › (IFC 4.3IFC – Industry Foundation Classes Open exchange format for building and plant models (BIM), standardized as ISO 16739. Background and sources ›) | Open data format for buildings and plants | Handover to building and building services; agree the scope of properties beforehand | 2024-09 |
| DEXPIDEXPI – Data Exchange in the Process Industry Vendor-neutral exchange format for P&IDs between different design programs. Background and sources › | Vendor-neutral exchange of P&IDs and process flow diagrams | Only via add-on tools – clarify with the client before the project starts | ongoing |
| ISO 15926-1ISO 15926 – Integration of life-cycle data for process plants Data model for exchanging plant data over the entire life cycle; the basis of many data models in large projects. Background and sources › | Life-cycle data of process plants | Basis of many data models in large projects; align property names with it | 2004 |
| IEC 81355-1IEC 81355 – Classification and designation of information and documents Successor of IEC 61355: part 1 specifies how documents are classified by kind and linked to the reference designation of the object. Background and sources ›, DIN EN 82045-1DIN EN 82045 – Document management Part 1 specifies principles and methods: metadata, life cycle and revisions of documents. Background and sources › | Classification of documents; document management | Document type as a title block property (DCCDCC – Document kind Classification Code Document kind classification code according to DIN EN IEC 61355-1: abbreviation for the kind of document, e.g. flow diagram or parts list. Background and sources ›); file names and revisions according to project rules | 2024 · 2002-11 |
| VDI 2770 Blatt 1VDI 2770 – Operation of process plants – Digital manufacturer information Part 1 specifies how manufacturers hand over their documentation in digital, machine-readable form. The tag links the documents to the component. Background and sources › | Digital manufacturer documentation | Assign manufacturer documents to the component via the tag | 2020-04 |
| NAMUR NE 100NE – NAMUR recommendation NAMUR worksheet, e.g. NE 100 (property lists for process control devices). Background and sources › | Property lists for process control devices | Name instrument properties according to the property list – simplifies data sheets and handover to E&I engineering | 2021-10 |
| DIN EN IECIEC – International Electrotechnical Commission International Electrotechnical Commission in Geneva: worldwide standards for electrical engineering and for instrumentation and control. Background and sources ›/IEEE 82079-1 | Instructions for use | Operating instructions for packages and plants; reference to P&ID and tags | 2021-09 |
Examples (values for illustration; the current standard and the manufacturer data govern):
- Instrument with property list: name properties such as “measuring range”, “process connection”, “explosion protection” according to NAMUR NE 100 – the data sheet of the E&I engineering adopts them without renaming.
- Document kind according to IEC 81355: P&ID and isometric with their document kind code (DCC) in the title block – so the common data environment finds all isometrics of a plant with one filter.
- IFC handover: before exporting, define which properties are included (e.g. tag, DN, piping spec, medium) – everything else stays in the Plant 3D project.
9 · Implementing in AutoCAD Plant 3D – in this order
- Define the rule set: describe symbol standard, identification system, sheet formats and layer scheme as the project standard (one page is enough).
- Create properties: every item that appears in an annotation, list or title block as a property of its own (DN, PN, medium, fluid group, piping spec, insulation, test group).
- Build tag formats: compose identifiers from the properties – never as free text.
- Symbols and classes: derive the library from the symbol standard, define layers and annotation per class.
- Piping specs and catalogs: build them according to DIN 21057-1; components from the product standards, valves according to manufacturer data.
- Templates: title block according to DIN EN ISO 7200, formats according to DIN EN ISO 5457 – for P&ID, ortho and iso from one source.
- Check: P&ID ↔ 3D comparison, clash detection, lists against the rule set.
Related offering
Ready configured
PlantConfig Pro provides this structure as a project template, the ASEING piping spec catalogs provide the matching catalogs. Preliminary sizing of piping specs with the Piping Spec Calculator.
Editions according to DIN Media, ISO, IEC, EUR-Lex and the issuing associations, research October 2026. Summaries in our own words; no standard texts, no standard tables. Check the current edition with the publisher before binding use.
Applicable codes and standards
| Area | Document | Contents | Edition | Status |
|---|---|---|---|---|
| Legislation | Directive 2014/68/EU (PED) | Pressure equipment, placing on the market | 2014 | valid |
| Legislation | BetrSichV | Operation and inspection of work equipment | 2015-02, last amended 2025 | valid |
| Flow diagram | DIN EN ISO 10628-1 | Flow diagrams: terms, types, representation | 2015-04 | valid |
| Flow diagram | DIN EN ISO 10628-2 | Graphical symbols | 2013-04 | valid |
| Flow diagram | DIN 28000-4 | Symbols for piping components (replaces DIN 2429) | 2014-07 | valid |
| Process control | DIN EN 62424 (VDE 0810-24VDE 0810 – VDE classification of process control standards Number under which a standard also applies as a VDE regulation: VDE 0810-24 is DIN EN 62424 (instrumentation in the flow diagram), VDE 0810-1 is DIN EN 61511-1 (functional safety). Background and sources ›) | Representation of process control tasks in the P&ID | 2017-12 | valid |
| Process control | ANSIANSI – American National Standards Institute US standards institute. ASME standards are usually also ANSI standards, hence the notation “ANSI/ASME B16.5”. Background and sources ›/ISA-5.1 | Instrumentation and Control Symbols (US) | 2024 (replaces 2022) | valid |
| Process control | DIN IEC 60050-351DIN IEC 60050 – International Electrotechnical Vocabulary Part 351 defines the terms of control technology, e.g. the difference between open-loop control and closed-loop control. Background and sources › | Control technology terms (replaces DIN 19226DIN 19226 – Control technology – Closed-loop and open-loop control engineering; terms Former terminology standard for control engineering, withdrawn. The terms are now in DIN IEC 60050-351. Background and sources ›) | 2014-09 | valid |
| Plant identification | DIN EN IEC 81346-1 / -2 | Structuring, reference designations, classes | 2024-07 / 2020-10 | valid |
| Plant identification | ISO 81346-10 | RDS-PP, power supply systems | 2022-08 | valid |
| Plant identification | VGB-S-811-01 | KKS Power Plant Classification System | 2018 | valid |
| Documentation | IEC 81355-1 | Classification of documents (DCC), replaces IEC 61355-1IEC 61355 – Classification and designation of documents for plants Classified documents using the document kind classification code DCC. Withdrawn at the end of 2024 and replaced by IEC 81355-1. Background and sources › | 2024 | valid |
| Piping | DIN EN 13480-1 to -6, -8 | Metallic industrial piping | 2024-12 (replaces 2017-12 + A1 ff.) | valid |
| Piping | DIN CEN/TR 13480-7 | Conformity assessment (technical report) | 2022-08 | valid |
| Piping specs | DIN 21057-1 | Basis for creating piping specs | 2023-08 (replaces 2016-12) | valid |
| Piping specs | DIN 21057-5 / -6 | Reinforced nozzles / flanges for machine prefabrication | 2016-12 | valid |
| Piping specs | DIN 21057-10 / -11 / -12 | Technical delivery conditions for piping components | 2026-04 / 2026-05 / 2026-04 | valid |
| Pipes | DIN EN 10216-1 / -2 / -3 / -4 / -5 | Seamless tubes for pressure purposes | 2014-03 / 2025-02 / 2014-03 / 2014-03 / 2021-06 | valid |
| Pipes | DIN EN 10217-1DIN EN 10217 – Welded steel tubes for pressure purposes – Technical delivery conditions Counterpart to DIN EN 10216 for welded pressure pipes, e.g. part 2 electric welded pipes for elevated temperatures, part 7 stainless steels. For welded pipes the weld joint factor z is added in the wall thickness calculation. Background and sources › to -6 / -7 | Welded tubes for pressure purposes | 2019-08 / 2021-06 | valid |
| Pipes | DIN EN ISO 3183DIN EN ISO 3183 – Petroleum and natural gas industries – Steel pipe for pipeline transportation systems Delivery conditions for steel line pipe (steel grades such as L245, L360) in the requirement levels PSL 1 and PSL 2. It replaces DIN EN 10208 and is used for gas and oil pipelines. Background and sources › | Line pipe (replaces EN 10208DIN EN 10208 – Steel pipes for pipelines for combustible fluids Delivery conditions for line pipe for gas and oil (requirement classes A and B). Withdrawn and replaced by DIN EN ISO 3183. Background and sources ›) | 2020-02 | valid |
| Pipes | DIN EN 10220 | Outside diameters and wall thicknesses (replaces DIN 2448DIN 2448 – Seamless steel tubes – Dimensions, masses per unit length Former German dimension standard for seamless steel pipes, withdrawn and replaced by DIN EN 10220. The outside diameters of series 1 have largely remained the same; wall thicknesses of old pipe specs often still come from DIN 2448. Background and sources › / 2458) | 2003-03 | valid |
| Fittings | DIN EN 10253-2 / -4 | Butt-welding fittings | 2026-07 / 2025-10 | valid |
| Flanges | DIN EN 1092-1 | Steel flanges, PN designated | 2018-12 | valid |
| Flanges | DIN EN 1514 / 1515 / 1591 / 1759 / 12560 | Gaskets, bolts, calculation, Class flanges | 1514-1:2024-10 · 1515-1:2000-01 · 1591-1:2026-02 · 1591-4:2013-12 · 1759-1:2005-02 · 12560-1:2024-10 | valid |
| Materials | DIN EN 10204DIN EN 10204 – Metallic products – Types of inspection documents Specifies the inspection documents used to prove material properties: 2.2 test report, 3.1 inspection certificate of the manufacturer, 3.2 with an independent inspector. The required type is stated in the piping spec. Background and sources › | Inspection certificates 3.1 / 3.2 | 2005-01 | valid |
| Materials | ISO 15608ISO 15608 – Welding – Grouping system for metallic materials Assigns materials to groups (e.g. group 1 non-alloy steels, group 8 austenitic steels). Welding procedures and welder qualifications are classified accordingly. Background and sources › | Grouping system for metallic materials (replaces ISO/TR 15608:2017) | 2025 | valid |
| Drawing | DIN EN ISO 7200 | Title blocks | 2004-05 | valid |
| Drawing | DIN EN ISO 5457 | Formats and drawing sheets | 2017-10 | valid |
| Drawing | DIN EN ISO 128-2 | Lines, basic conventions | 2023-06 (replaces 2022-02) | valid |
| Plant identification | DIN 2403 | Identification of pipelines according to fluid conveyed | 2025-12 (replaces 2018-10) | valid |
Withdrawn standards and their successors
For working with as-built documentation that still refers to old standards.
| Previously cited | Status | To be applied today |
|---|---|---|
| DIN EN ISO 10628:2001 | replaced | DIN EN ISO 10628-1:2015 and -2:2013 |
| DIN 2429-1 / -2 | withdrawn | DIN 28000-4:2014 |
| DIN 19227-1DIN 19227 – Control technology – Graphical symbols and identifying letters for process control engineering Former German standard for instrumentation code letters, withdrawn. Replaced by DIN EN 62424 and DIN 28000-4; older P&IDs still show its notation. Background and sources › | replaced | DIN EN 62424:2017-12 |
| ISO 3511-1ISO 3511 – Process measurement and control functions – Symbolic representation Former ISO standard for instrumentation symbols, withdrawn in April 2025; successor ISO 14617-2:2025. In Germany DIN EN 62424 applies. Background and sources › | withdrawn | ISO 14617-2:2025 (ISO 3511-1 withdrawn 04/2025); in Germany DIN EN 62424:2017-12 |
| ISA S5.1 | replaced | ANSI/ISA-5.1-2024 |
| DIN 19226 | withdrawn | DIN IEC 60050-351:2014-09 |
| EN 61346IEC 61346 – Industrial systems – Structuring principles and reference designations (old) Predecessor of IEC 81346, withdrawn. Older designation guidelines still refer to it. Background and sources › | replaced | DIN EN IEC 81346-1:2024-07 / -2:2020-10 |
| DIN 6779-1DIN 6779 – Designation system for technical products and technical product documentation Former German designation standard. Parts 1, 2 and 10 are withdrawn and have been merged into DIN EN IEC 81346 and ISO/TS 81346-10. Background and sources ›, -2, -10 | withdrawn | DIN EN IEC 81346-1:2024-07 / -2:2020-10, ISO 81346-10:2022 |
| ISO/TS 16952-10ISO/TS 16952 – Technical product documentation – Reference designation system Former ISO specification for reference designation; part 10 was the version for power plants (RDS-PP). Now listed as ISO/TS 81346-10. Background and sources › (RDS-PP) | replaced | ISO 81346-10:2022 (also replaces ISO/TS 81346-10) |
| VGB B105B 105/B 106 – VGB guidelines on KKS Former VGB guidelines on the power plant identification system (KKS). Today the standard VGB-S-811-01 applies. Background and sources › / B106 | replaced | VGB-S-811-01 (2018) |
| Directive 97/23/EC | replaced | Directive 2014/68/EU (since 19 July 2016) |
| GPSGGPSG – German Equipment and Product Safety Act (GPSG) Former German product safety act. It applied until 2011 and was replaced by the Product Safety Act (ProdSG). Background and sources ›, Pressure Vessel Ordinance, Steam Boiler Ordinance | withdrawn | ProdSG 2021, BetrSichV 2015, ÜAnlG |
| DIN 2470-1DIN 2470 – Gas pipelines made of steel pipes up to 16 bar – Requirements for pipeline components Old standard for gas pipelines, withdrawn. Today DIN EN 12007 applies (gas infrastructure up to 16 bar), and DIN EN 13480 for industrial plants. Background and sources › (gas pipelines ≤ 16 bar) | withdrawn | DIN EN 12007-1:2012-10 / -3:2015-07; for industrial plants DIN EN 13480 |
| DIN 1626DIN 1626 – Welded circular tubes of non-alloy steels with specified requirements Old German pipe standard, withdrawn. Its successor is DIN EN 10217-1; depending on the application also DIN EN 10224, DIN EN 10296-1 or DIN EN ISO 3183. Designations according to DIN 1626 are still found in existing plants and old pipe specs. Background and sources ›, 1628, 1629, 1630, 17175, 17177 | withdrawn | DIN EN 10216-x / 10217-x |
| DIN 2448, DIN 2458DIN 2458 – Welded steel tubes – Dimensions, masses per unit length Former German dimension standard for welded steel pipes, withdrawn and, like DIN 2448, replaced by DIN EN 10220. Background and sources › | withdrawn | DIN EN 10220:2003-03 |
| DIN 2413-1DIN 2413 – Seamless steel tubes for oil and water hydraulic systems – Calculation basis Today it only applies to hydraulic pipes under pulsating load. The former parts 1 and 2 for general piping are withdrawn; there the calculation follows DIN EN 13480-3. Background and sources › / -2:1993 | withdrawn | DIN EN 13480-3:2024-12 (DIN 2413:2020-04 now applies only to hydraulic tubes) |
| DIN 50049DIN 50049 – Metallic products – Types of inspection documents (old) Predecessor of DIN EN 10204, withdrawn. Old designations such as “3.1B” and “3.1C” correspond today to 3.1 and 3.2. Background and sources › (3.1B / 3.1C) | withdrawn | DIN EN 10204:2005-01 (3.1 / 3.2) |
| DIN 2513DIN 2513 – Spigot and recess on flanges, PN 10 to 100 Old standard for flanges with spigot and recess, withdrawn. Today these sealing faces are called type E and F in DIN EN 1092-1. Background and sources › | withdrawn | DIN EN 1092-1:2018-12 |
| DIN EN 10208 | replaced | DIN EN ISO 3183:2020-02 |
| PAS 1057 | replaced | DIN 21057-1:2023-08 and subsequent parts |
| DIN CEN/TS 1591-4:2007-10DIN EN 1591 – Flanges and their joints – Design rules for gasketed circular flange connections Calculation method for tight and strong flange connections (part 1). The gasket parameters are provided by DIN CEN/TR 1591-2 or DIN EN 13555; part 4 (now DIN CEN/TS 1591-4) covers the qualification of fitters. Background and sources › | replaced | DIN EN 1591-4:2013-12 (personnel qualification) |
| EN 1092-1:2007 | replaced | DIN EN 1092-1:2018 |
| CRCR – CEN Report Report from CEN (CEN Report). Such documents are now called CEN/TR (Technical Report). Background and sources › ISO 15608:2000 | replaced | ISO/TR 15608:2017, now ISO 15608:2025 |
| DIN ISO 128-24 | replaced | DIN EN ISO 128-2:2023-06 |
| DIN 6771-1DIN 6771 – Title blocks for drawings, plans and lists (old) Former standard for title blocks, withdrawn and replaced by DIN EN ISO 7200. Many company title blocks are still based on it. Background and sources › | replaced | DIN EN ISO 7200:2004-05 |
| IEC 61355-1:2008 | withdrawn | IEC 81355-1:2024 (IEC 61355-1 withdrawn 12/2024) |
| ISO/TR 15608:2017 | replaced | ISO 15608:2025 |
| DIN EN 1591-2:2008-09 | withdrawn | DIN CEN/TR 1591-2:2023-12 |
| DIN EN 1591-1:2014-04 | replaced | DIN EN 1591-1:2026-02 |
| DIN 21057-10 / -11 / -12:2017-04 | replaced | Editions 2026-04 / 2026-05 / 2026-04 |
| DIN EN 10253-2:2021-11 / -4:2008-06 | replaced | DIN EN 10253-2:2026-07 / -4:2025-10 |
| ASME B36.10-2018 / B36.19M-2018B36.10M – ASME B36.10M Steel Pipe US dimensional standard for welded and seamless steel pipes: outside diameters and wall thicknesses (schedule). Background and sources ›B36.19 – ASME B36.19 US dimensional standard for stainless steel pipe: outside diameters and wall thicknesses (schedule with “S”, e.g. 10S). Background and sources › | replaced | ASME B36.10-2022 / B36.19-2022 (without "M") |
| ASME B16.5-2020 / B16.9-2018 / B31.3-2022B16.5 – ASME B16.5 Flanges US standard for flanges and flanged fittings from NPS ½ to NPS 24 in pressure classes Class 150 to 2500. Background and sources ›B16.9 – ASME B16.9 US standard for butt-welding fittings: elbows, tees, reducers and caps. Background and sources ›B31.3 – ASME B31.3 Process Piping US code for process piping: materials, design, fabrication and testing of piping in chemical and process plants. Background and sources › | replaced | ASME B16.5-2025 / B16.9-2024 / B31.3-2024 |
| DIN EN 81346-1:2010-05 | replaced | DIN EN IEC 81346-1:2024-07 |
| ISO 14617-3 to -15 | replaced | ISO 14617-2:2025 (consolidates the former parts) |
| Directive 2006/42/EC (machinery) | replaced from 20.01.2027 | Regulation (EU) 2023/1230 |
| DIN EN 593:2018-01DIN EN 593 – Industrial valves – Metallic butterfly valves Product standard for metallic butterfly valves (concentric and eccentric, wafer and flanged type). Background and sources › | new edition announced | DIN EN 593:2026-11 |
Sources
- DIN Media (standard status and replacement notes)
- ISO 3511-1 (Status)
- ANSI/ISA-5.1-2024
- VGB-S-811-01 KKS
- BG RCI: DIN standards for piping (05/2025)
- Text summaries: Wikipedia articles and specialist websites, each linked at the end of the chapter
Looking for ready-made catalogs to DIN EN?

Before you go …
Don't miss any training dates, C³ invitations and news on AutoCAD Plant 3D and P&ID.
Our newsletter only arrives when there's something important – concise and with tips from practice.
Technically responsible: A. Seitz, Managing Director of A. Seitz Ingenieur GmbH (plant design, AutoCAD Plant 3D).
Terms, background and sources 153 terms on this page
Brief explanations for reference. They do not replace the standard or code itself.
- R&I – Piping and instrumentation diagram
Flow diagram showing all pipes, valves, equipment and instrumentation of a plant (P&ID, Piping and Instrumentation Diagram).
Symbols and drawing rules: DIN EN ISO 10628-1 and -2. Identification letters for instrumentation: DIN EN 62424 or ISA-5.1.
- EN – European Standard
European Standard, developed by CEN (general) or CENELEC (electrical engineering).
Every member country must adopt an EN unchanged as a national standard – in Germany as “DIN EN …”. Conflicting national standards are withdrawn.
- CEN – European Committee for Standardization
European Committee for Standardization in Brussels. It develops the European Standards (EN) outside electrical engineering.
- DIN – German Institute for Standardization
German Institute for Standardization in Berlin: it publishes the German standards (DIN standards) and represents Germany in CEN and ISO.
DIN was founded in 1917 as the Standards Committee of German Industry. If “DIN EN” or “DIN EN ISO” precedes the number, a European or international standard has been adopted unchanged as a German standard.
- ÖNORM – Austrian standard
Standard of Austrian Standards. “ÖNORM EN” is a European Standard adopted in Austria.
- SN – Swiss standard
Standard of the Swiss Association for Standardization SNV. “SN EN” is a European Standard adopted in Switzerland.
- NEN – Dutch standard
Standard of the Dutch standards body NEN. “NEN-EN” is a European Standard adopted in the Netherlands.
- BS – British Standard
British standard of the standards body BSI. “BS EN” is a European Standard adopted in the United Kingdom.
- NF – Norme française
French standard of the standards body AFNOR. “NF EN” is a European Standard adopted in France.
- UNE – Una Norma Española
Spanish standard of the standards body UNE. “UNE-EN” is a European Standard adopted in Spain.
- ISO – International Organization for Standardization
International Organization for Standardization in Geneva: it develops standards that apply worldwide (ISO standards).
ISO was founded in 1947. Its members are the national standards bodies; for Germany, this is DIN.
- DIN 21057 – Piping specs for process plants
Series of standards for structuring piping specs: part 1 fundamentals and naming, further parts per material. It is the successor of PAS 1057; ASEING piping specs are based on it.
- DIN 2403 – Identification of pipelines according to fluid conveyed
DIN 2403 specifies how above-ground pipelines are marked according to the fluid they carry. Each fluid belongs to a group 0 to 9 with its own group colour; flammable and non-flammable gases, liquids and solids also carry an additional colour. “Gr.” with a number names the group, e.g. Gr. 1 = water, green.
Groups and colours: 1 water – green · 2 steam – red · 3 air – grey · 4 flammable gases – yellow, additional colour red · 5 non-flammable gases – yellow, additional colour black · 6 acids – orange · 7 alkalis – violet · 8 flammable liquids and solids – brown, additional colour red · 9 non-flammable liquids and solids – brown, additional colour black · 0 oxygen – blue (as reproduced in TRGS 201 Annex 3, Table 2).
In the Piping Spec Calculator the groups order the selection of fluids. “Exhaust air and flue gas” is listed under 3/5; food and pharma and “other” have no group. The group does not determine material or pressure rating – it applies to marking the finished line.
Current edition according to DIN Media: DIN 2403:2025-12 (replaces DIN 2403:2018-10). Not covered are pipelines on ships and marine installations, ventilation systems in non-residential buildings and medical gas pipelines.- AD 2000 – AD 2000 Code
German code for pressure vessels: calculation, materials and manufacture. Working to it meets the requirements of the Pressure Equipment Directive.
- TRBS – Technical Rules for Operational Safety
Technical rules for the German Ordinance on Industrial Safety and Health, e.g. on the inspection of pressure systems.
- EU – European Union
European Union. Since the Treaty of Lisbon (end of 2009) the numbers of legal acts contain “EU”, e.g. Directive 2014/68/EU.
- DIN EN 13480 – Metallic industrial piping
The European standard for metallic industrial piping: part 2 materials, part 3 design and calculation, part 4 fabrication, part 5 inspection and testing. The Piping Spec Calculator sizes wall thicknesses according to part 3 – as a preliminary sizing, not a piping design.
Current parts 1 to 6 and 8 in the 2024-12 edition; part 7 (conformity assessment) is a technical report, DIN CEN/TR 13480-7.
- ATEX – Directive 2014/34/EU
Short name of EU Directive 2014/34/EU for equipment and protective systems in potentially explosive atmospheres (from French “ATmosphères EXplosibles”).
- AwSV – German ordinance on facilities handling substances hazardous to water (AwSV)
German ordinance on how plants handling substances hazardous to water are built, operated and inspected. It also determines the water hazard class (WGK).
- TA Luft – Technical Instructions on Air Quality Control
Administrative regulation under the German Federal Immission Control Act. It limits emissions from plants and sets requirements, e.g., for the tightness of flanged joints.
- VDI 2290 – Emission control – Characteristic values for tight flange connections
Specifies the TA Luft (German Clean Air Regulations) requirements for “technically tight” flange connections: gasket selection, proof of tightness, assembly.
- CAD – Computer-Aided Design
Computer-aided design and drafting.
- DN – Nominal size (DN)
Designation for the size of pipes, fittings and valves (Diameter Nominal). It is roughly the inside diameter in millimeters but is not an exact dimension.
Specified in DIN EN ISO 6708. Which outside diameter belongs to a DN is defined in the dimensional standards, e.g. DIN EN 10220 for steel pipes.
- PS – maximum allowable pressure
Maximum allowable pressure according to the Pressure Equipment Directive, in bar gauge, set by the manufacturer. Together with the volume V or the nominal size DN it determines the category of the pressure equipment.
- bar – Unit of pressure
Unit of pressure: 1 bar = 100,000 Pa = 0.1 MPa. In plant engineering, it usually refers to the gauge pressure relative to the surroundings (often “barg” or, in German, “bar ü”).
- DIN EN ISO 6708 – Pipework components – Definition and selection of DN (nominal size)
Defines the nominal size DN as a dimensionless reference number, not as a dimension. The actual outside diameter is in the catalog, e.g. DN 100 = 114.3 mm for steel pipe.
- DIN EN 1333 – Flanges and their joints – Pipework components – Definition and selection of PN
Defines the nominal pressure PN as a reference number, not as the permissible pressure, and sets the PN series (PN 2.5 to PN 400). Which pressure is permissible at which temperature is stated in the product standard.
- PN – Nominal pressure rating
Designation for the pressure rating of flanges and valves (Pressure Nominal), e.g. PN 16. It corresponds roughly to the allowable pressure in bar at room temperature; at higher temperatures, less is allowed.
Specified in DIN EN 1333. The pressure-temperature ratings for each material are given in the component standards, e.g. DIN EN 1092-1 for steel flanges.
- DIN EN 764 – Pressure equipment – Terminology
Part 1 specifies the terms for pressure equipment: pressure, temperature, volume, nominal size. This way design and operating data have the same names everywhere in properties and lists.
- ISO 80000 – Quantities and units
Part 1 covers how quantities and units are written, e.g. a space between number and unit. This way units are shown consistently in properties and labels.
- DIN EN 10220 – Seamless and welded steel tubes – General tables of dimensions and masses per unit length
The basic table of outside diameters and wall thicknesses of steel pipes (series 1 to 3). The Piping Spec Calculator takes the outside diameter per DN from it (series 1), e.g. 114.3 mm for DN 100.
Replaces the former DIN 2448 and DIN 2458; the prestandard was called DIN V ENV 10220. Current edition 2003-03 (DIN Media).
- DIN EN 1057 – Copper and copper alloys – Seamless round copper tubes for water and gas (sanitary and heating)
Dimensions and tempers of copper tubes in building services, e.g. 108 × 2.5 mm instead of 114.3 mm for steel pipe. In the Piping Spec Calculator the temper (R220, R250, R290) determines the strength.
- PE – Polyethylene
Polyethylene, a thermoplastic for gas, water and wastewater pipes. “PE 100” indicates the strength class (MRS 10 MPa).
Abbreviations for plastics according to DIN EN ISO 1043-1.
- DIN EN 1092 – Flanges and their joints – Circular flanges, PN designated
The flange standard by nominal pressure PN; part 1 covers steel flanges with types (e.g. type 11 weld neck flange), sealing faces (B1, C, D …) and dimensions. Annex G assigns the permissible pressure to the temperature for each material group.
- DIN EN ISO 10628 – Diagrams for the chemical and petrochemical industry
Part 1 specifies the kinds of flow diagrams (block, process, P&I diagram) and what each shows; part 2 the graphical symbols. Basis of the symbol library in AutoCAD P&ID.
- DIN 28000 – Chemical apparatus – Documentation in the life cycle of process plants
Part 4 contains the graphical symbols for valves, pipelines and actuators in the flow diagram. It replaces DIN 2429 and complements DIN EN ISO 10628-2.
- DIN 2429 – Graphical symbols for technical drawings – Pipelines
Former symbol standard for pipelines and valves, withdrawn and replaced by DIN 28000-4.
- ISO 14617 – Graphical symbols for diagrams
Series of standards for symbols in diagrams of all disciplines. Part 1 general rules; since 2025 the former parts 3 to 15 are combined in part 2.
- ISO 15519 – Specification for diagrams for the process industry
Part 1 covers general rules, part 2 measurement and control in diagrams of the process industry.
- DIN EN 62424 – Representation of process control engineering requests in P&I diagrams
Specifies how instrumentation points are represented in the P&ID and designated with code letters (e.g. TIC = temperature, indication, control). It replaces DIN 19227-1; VDE classification VDE 0810-24.
- CAEX – Computer Aided Engineering Exchange
XML format according to IEC 62424 for exchanging design data, e.g. instrumentation loops, between programs.
- ANSI/ISA-5.1 – Instrumentation and Control – Symbols and Identification
US counterpart to DIN EN 62424: symbols and code letters for instruments in flow diagrams (e.g. FIC, PT). AutoCAD P&ID has its own ISA symbol library for it; do not mix with DIN EN 62424.
Formerly ISA S5.1; current edition ANSI/ISA-5.1-2024.
- US – United States
United States of America.
- ISA – International Society of Automation
US association for automation. Its standard ISA-5.1 specifies symbols and identification letters for instrumentation.
- IEC 60617 – Graphical symbols for diagrams (database)
The database of graphical symbols for electrical engineering. Used in the P&ID for electrical symbols such as motor or heater.
- DIN EN 61511 – Functional safety – Safety instrumented systems for the process industry sector
Application of functional safety in the process industry: safety functions are designed for a target SIL. In the P&ID such control points must be marked recognisably.
- SIL – Safety Integrity Level
Safety level 1 to 4 for safety functions according to IEC 61508 and IEC 61511 – the higher the level, the less often the safety function may fail.
- DIN EN 61508 – Functional safety of electrical/electronic/programmable electronic safety-related systems
Basic standard of functional safety for devices and manufacturers (SIL 1 to 4). In the P&ID it only appears as a property, e.g. the SIL capability of a device.
- DIN EN ISO 7200 – Technical product documentation – Data fields in title blocks and document headers
Specifies the data fields of the title block, including seven mandatory fields such as identification number, title, creator and date of issue. Width 180 mm, position bottom right.
- DIN EN ISO 5457 – Technical product documentation – Sizes and layout of drawing sheets
Covers sheet sizes, frames (20 mm filing margin on the left, 10 mm elsewhere), grid zones and folding marks of drawing sheets.
- DWG – AutoCAD drawing format
AutoCAD file format for drawings and 3D models; AutoCAD Plant 3D and AutoCAD P&ID also save in this format.
- A0 … A4 – Paper sizes
Paper sizes according to DIN EN ISO 216: A4 = 210 × 297 mm. Each smaller number doubles the area (A3 = 297 × 420 mm, A0 = about 1 m²).
- DIN EN ISO 3098 – Technical product documentation – Lettering
Covers standard lettering in drawings: lettering types A and B, character heights from 2.5 mm.
- DIN EN ISO 128 – Technical product documentation – General principles of representation
Series of standards for representation in drawings; part 2 covers the line types (continuous, dashed, dash-dot line) and replaces DIN ISO 128-24.
- DIN ISO 5455 – Technical drawings – Scales
Specifies the recommended scales, e.g. 1:2, 1:5, 1:10 and their multiples of ten, as well as enlargements 2:1, 5:1.
- DIN EN ISO 13567 – Technical product documentation – Organization and naming of layers for CAD
Part 1 covers a key for layer names (responsible party, element, presentation). Useful when layers are coordinated with construction or building services.
- DIN EN IEC 81346 – Industrial systems – Structuring principles and reference designations
The cross-industry basis of plant designation: each object under three aspects – function (=), product (-) and location (+). Part 2 contains the code letters, ISO/TS 81346-10 the version for power plants (RDS-PP).
- KKS – Power plant identification system
Identification of plants, systems, equipment units and components in power plants according to guideline VGB-S-811-01.
A KKS code is structured from coarse to fine: overall plant, system, equipment unit, component. Its successor is RDS-PP according to ISO/IEC 81346.
- RDS-PP – Reference Designation System for Power Plants
Identification system for power plants based on the international standard series ISO/IEC 81346; successor to KKS.
- DIN EN ISO 7010 – Graphical symbols – Safety colours and safety signs – Registered safety signs
The collection of warning, prohibition, mandatory and safe condition signs. Together with DIN 2403 it determines the signs on pipelines.
- DIN EN 10216 – Seamless steel tubes for pressure purposes – Technical delivery conditions
Series of standards for seamless pressure pipes: part 1 non-alloy steels at room temperature, part 2 steels for elevated temperatures (e.g. P235GH), part 5 stainless steels. It provides the strength values the Piping Spec Calculator uses for the preliminary sizing of the wall thickness.
- DIN EN 10253 – Butt-welding fittings
Series of standards for butt-welding elbows, tees, reducers and caps; part 2 for non-alloy and ferritic steels, part 4 for austenitic steels. In the piping spec, fittings usually refer to part 2 or 4.
- DIN EN 1514 – Flanges and their joints – Dimensions of gaskets for PN-designated flanges
Dimension standard for flange gaskets: part 1 flat gaskets of non-metallic material, further parts spiral wound and kammprofile gaskets. The gasket thus fits the flange according to DIN EN 1092-1.
- DIN EN 1515 – Flanges and their joints – Bolting
Covers selection (part 1) and material combinations (part 2) of bolts and nuts for flange connections, e.g. 25CrMo4 at higher temperatures.
- DIN EN 13555 – Flanges and their joints – Gasket parameters and test procedures
Specifies how gasket parameters (e.g. minimum surface pressure, creep relaxation) are measured. The flange calculation according to DIN EN 1591-1 needs these values.
- DIN EN 736 – Industrial valves – Terminology
Part 1 defines the basic types (globe valve, gate valve, plug valve, butterfly valve), further parts terms and nominal sizes. This way valves are named consistently in the catalog.
- DIN EN 19 – Industrial valves – Marking of metallic valves
Specifies what must be marked on a valve: nominal size, nominal pressure, material, manufacturer, flow direction.
- DIN EN 1983 – Industrial valves – Steel ball valves
Product standard for steel ball valves: designs, end connections, tests. In the valve catalog it is listed for the ball valves.
- DIN EN ISO 4126 – Safety devices for protection against excessive pressure
Part 1 covers safety valves. Inlet and outlet nominal sizes are usually different – state them separately in the component and show the blow-off line in the P&ID.
- DIN EN 14917 – Metal bellows expansion joints for pressure applications
Covers design, manufacture and testing of metal expansion joints. In Plant 3D they are a separate component class with installation length and pretension according to the manufacturer.
- DIN EN 10226 – Pipe threads where pressure-tight joints are made on the threads
Taper external thread (R) with parallel or taper internal thread (Rp, Rc), sealing in the thread. Not to be confused with the parallel G thread according to DIN EN ISO 228.
- DIN EN ISO 228 – Pipe threads where pressure-tight joints are not made on the threads
Parallel G thread; it does not seal in the thread but via a seal ring or flat gasket. Typical on valves and fittings.
- DIN EN 10255 – Non-alloy steel tubes suitable for welding and threading
The classic threaded pipes (formerly DIN 2440/2441) in the medium and heavy series, for water, air and heating. They are threaded according to DIN EN 10226-1.
- DIN EN 10241 – Steel threaded pipe fittings
Threaded steel fittings (sockets, nipples, elbows) for threaded pipes according to DIN EN 10255.
- DIN EN 10242 – Malleable cast iron threaded pipe fittings
Malleable cast iron threaded fittings (the typical “building services fittings”). Design and pressure rating are indicated by code letters.
- DIN EN ISO 15494 – Plastics piping systems for industrial applications – PB, PE, PE-RT, PE-X, PP
Counterpart to DIN EN ISO 15493 for polyolefins. The Piping Spec Calculator uses it to calculate plastic pipes via the allowable stress σ = MRS/C and the SDR series.
- DIN EN ISO 15493 – Plastics piping systems for industrial applications – ABS, PVC-U, PVC-C
Requirements for pipes, fittings and valves made of ABS, PVC-U and PVC-C in industrial applications. Plastic pipe specs are built by SDR instead of wall thickness per DN.
- DIN EN 12201 – Plastics piping systems in PE for water supply
Series of standards for PE pressure pipe systems in water supply; part 2 covers the pipes. For industrial PE piping, DIN EN ISO 15494 applies.
- SDR – Standard Dimension Ratio
Ratio of outside diameter to wall thickness for plastic pipes, e.g. SDR 11. A smaller SDR means a thicker wall and a higher allowable pressure.
The series are specified in ISO 4065.
- P235GH – Steel name for pressure equipment
Steel designation according to DIN EN 10027-1: P = steel for pressure vessels and pressure pipes, number = minimum yield strength in MPa, letters = properties (e.g. GH for elevated temperatures, NL for low temperatures).
- MPa – Megapascal
Unit of pressure and mechanical stress: 1 MPa = 1 N/mm² = 10 bar.
- B1, B2 – Sealing face type according to DIN EN 1092-1
Shape of a flange sealing face: B1 = raised face (roughness Rz up to 50 µm), B2 = raised face, finer machined (Rz up to 12.5 µm).
- N/mm² – Newtons per square millimeter
Unit of mechanical stress, e.g. yield strength or allowable stress: 1 N/mm² = 1 MPa.
- ISO 6412 – Technical drawings – Simplified representation of pipelines
Part 1 covers basic rules and orthogonal representation, part 2 isometric representation. The isometrics from AutoCAD Plant 3D follow these rules.
- DIN EN ISO 3834 – Quality requirements for fusion welding
Specifies the quality requirements a welding company must meet (comprehensive, standard, elementary). Basis for fabricating piping according to DIN EN 13480.
- DIN EN ISO 9606 – Qualification testing of welders – Fusion welding
Covers welder qualification testing; part 1 for steel. Without a valid qualification, welding on pressure piping is not permitted.
- DIN EN ISO 15614 – Specification and qualification of welding procedures – Welding procedure test
Part 1 covers the procedure test for steel and nickel: a welding procedure is qualified on a test piece and then described in the WPS.
- DIN EN ISO 5817 – Welding – Quality levels for imperfections
Specifies the quality levels B, C and D for welds (B = highest requirement). The required level is stated per piping spec.
- DIN EN ISO 17636 – Non-destructive testing of welds – Radiographic testing
Part 1 covers radiographic testing with film. Extent and testing class are specified in the weld list per piping spec.
- DIN 4140 – Insulation work on industrial and building services installations
Covers the execution and materials of thermal and cold insulation. In Plant 3D the insulation thickness affects clearances, support heights and clash detection.
- AGI – Industrial construction association (Arbeitsgemeinschaft Industriebau)
Arbeitsgemeinschaft Industriebau e. V. (industrial construction association). Its worksheets, e.g. AGI Q 101 on insulation work, are widely used design references in industry.
- VDI 2055 – Thermal and cold insulation of operational installations
Part 1 covers the calculation of heat losses and insulation thicknesses. It complements DIN 4140, which covers the installation.
- DIN EN ISO 12944 – Corrosion protection of steel structures by protective paint systems
Series of standards for paint systems: corrosivity categories C1 to CX and durability. The paint system is stated as a property of the pipeline.
- DIN EN IEC 60079-10 – Explosive atmospheres – Classification of areas
Part 1 covers the classification of areas with explosive gas atmospheres into zones 0, 1 and 2. In Plant 3D the zones can be shown and checked as solids.
- DIN EN 1672 – Food processing machinery – Hygiene requirements
Part 2 specifies how machines and plants for food must be designed hygienically: cleanable surfaces, no dead spaces, drainability. For the piping spec this means connections without dead space and a defined surface finish.
- EHEDG – European Hygienic Engineering & Design Group
European professional association with guidelines for hygienic design in food and pharmaceutical plants.
- DIN 11850 – Stainless steel tubes for the food and chemical industry – Dimensions, materials
Specifies outside diameters, wall thicknesses (series 1 to 3) and materials of stainless steel tubes for food, chemical and pharmaceutical plants. In the Piping Spec Calculator, “DIN 11850 series 2” is the usual hygienic tube series.
The pipes are usually orbital welded; detachable joints follow DIN 11851 (union) or DIN 32676 (clamp), aseptic joints DIN 11864.
- DIN EN 1775 – Gas supply – Gas pipework for buildings
Covers gas pipework in buildings up to 5 bar. In Germany DVGW-TRGI and DVGW G 459 supplement the standard.
- DVGW G 459 – DVGW worksheet G 459 – Gas service connections
Part 1 covers planning and construction of gas service connections up to the main shut-off device. Decisive for gas piping specs and shut-offs in the connection area.
- DIN EN 12007 – Gas infrastructure – Pipelines for maximum operating pressure up to and including 16 bar
Series of standards for public gas supply pipelines; part 1 general requirements, part 3 steel pipelines. It replaces the former DIN 2470.
- DIN EN 253 – District heating pipes – Bonded single pipe systems with plastic casing
Covers district heating bonded pipes: steel service pipe, PUR insulation, PE casing. That is why the catalog also lists the casing outside diameter.
- DIN EN 13941 – District heating pipes – Design and installation of bonded pipe systems
Part 1 covers design, structural analysis and installation of buried district heating pipelines made of bonded pipes, including compensation of expansion.
- DIN EN 806 – Specifications for installations inside buildings conveying water for human consumption
Series of standards for drinking water installations inside buildings: planning, sizing, installation and operation. In Germany DIN 1988 supplements the series.
- DIN 1988 – Codes of practice for drinking water installations (national supplement)
German supplement to DIN EN 806; part 100 covers the protection of drinking water and the choice of materials.
- DIN EN 378 – Refrigerating systems and heat pumps – Safety and environmental requirements
Part 1 covers basic requirements and divides refrigerants into safety groups (e.g. A1, A2L, B2L). The refrigerant is thus treated like a fluid of the piping spec.
- DIN EN 1443 – Chimney systems – General requirements
Basic standard for chimneys: classification by temperature, pressure, condensate resistance and corrosion. Flue gas lines usually do not fall under the Pressure Equipment Directive.
- DIN EN 1856 – Chimney systems – Requirements for metal chimneys
Part 1 covers metal system chimneys, part 2 flue liners and connecting flue pipes. It applies together with DIN EN 1443.
- DIN 11864 – Stainless steel valves for aseptic, chemical and pharmaceutical applications
Series of standards for aseptic connections with minimal dead space: part 1 unions, further parts flange and clamp connections. It is chosen when work is sterile and DIN 11851 or DIN 32676 are not sufficient.
- DIN EN ISO 19650 – Information management using BIM
Part 1 specifies the terms and principles of information management: roles, processes and the common data environment (CDE), e.g. Autodesk Docs.
- BIM – Building Information Modeling
Planning, building and operating with a digital model that contains not only the geometry but also the properties of the components.
- DIN EN ISO 16739 – Industry Foundation Classes (IFC) for data sharing in the construction and facility management industries
The open data format IFC (currently IFC 4.3) for exchange with construction and building services.
- IFC – Industry Foundation Classes
Open exchange format for building and plant models (BIM), standardized as ISO 16739.
- DEXPI – Data Exchange in the Process Industry
Vendor-neutral exchange format for P&IDs between different design programs.
- ISO 15926 – Integration of life-cycle data for process plants
Data model for exchanging plant data over the entire life cycle; the basis of many data models in large projects.
- IEC 81355 – Classification and designation of information and documents
Successor of IEC 61355: part 1 specifies how documents are classified by kind and linked to the reference designation of the object.
- DIN EN 82045 – Document management
Part 1 specifies principles and methods: metadata, life cycle and revisions of documents.
- DCC – Document kind Classification Code
Document kind classification code according to DIN EN IEC 61355-1: abbreviation for the kind of document, e.g. flow diagram or parts list.
- VDI 2770 – Operation of process plants – Digital manufacturer information
Part 1 specifies how manufacturers hand over their documentation in digital, machine-readable form. The tag links the documents to the component.
- NE – NAMUR recommendation
NAMUR worksheet, e.g. NE 100 (property lists for process control devices).
- IEC – International Electrotechnical Commission
International Electrotechnical Commission in Geneva: worldwide standards for electrical engineering and for instrumentation and control.
IEC was founded in 1906. IEC standards adopted in Europe are called “EN IEC …” or “EN 6xxxx”.
- VDE 0810 – VDE classification of process control standards
Number under which a standard also applies as a VDE regulation: VDE 0810-24 is DIN EN 62424 (instrumentation in the flow diagram), VDE 0810-1 is DIN EN 61511-1 (functional safety).
- ANSI – American National Standards Institute
US standards institute. ASME standards are usually also ANSI standards, hence the notation “ANSI/ASME B16.5”.
- DIN IEC 60050 – International Electrotechnical Vocabulary
Part 351 defines the terms of control technology, e.g. the difference between open-loop control and closed-loop control.
- DIN 19226 – Control technology – Closed-loop and open-loop control engineering; terms
Former terminology standard for control engineering, withdrawn. The terms are now in DIN IEC 60050-351.
- IEC 61355 – Classification and designation of documents for plants
Classified documents using the document kind classification code DCC. Withdrawn at the end of 2024 and replaced by IEC 81355-1.
- DIN EN 10217 – Welded steel tubes for pressure purposes – Technical delivery conditions
Counterpart to DIN EN 10216 for welded pressure pipes, e.g. part 2 electric welded pipes for elevated temperatures, part 7 stainless steels. For welded pipes the weld joint factor z is added in the wall thickness calculation.
- DIN EN ISO 3183 – Petroleum and natural gas industries – Steel pipe for pipeline transportation systems
Delivery conditions for steel line pipe (steel grades such as L245, L360) in the requirement levels PSL 1 and PSL 2. It replaces DIN EN 10208 and is used for gas and oil pipelines.
- DIN EN 10208 – Steel pipes for pipelines for combustible fluids
Delivery conditions for line pipe for gas and oil (requirement classes A and B). Withdrawn and replaced by DIN EN ISO 3183.
- DIN 2448 – Seamless steel tubes – Dimensions, masses per unit length
Former German dimension standard for seamless steel pipes, withdrawn and replaced by DIN EN 10220. The outside diameters of series 1 have largely remained the same; wall thicknesses of old pipe specs often still come from DIN 2448.
- DIN EN 10204 – Metallic products – Types of inspection documents
Specifies the inspection documents used to prove material properties: 2.2 test report, 3.1 inspection certificate of the manufacturer, 3.2 with an independent inspector. The required type is stated in the piping spec.
- ISO 15608 – Welding – Grouping system for metallic materials
Assigns materials to groups (e.g. group 1 non-alloy steels, group 8 austenitic steels). Welding procedures and welder qualifications are classified accordingly.
Since October 2025 a standard, ISO 15608:2025; before that technical report ISO/TR 15608:2017.
- DIN 19227 – Control technology – Graphical symbols and identifying letters for process control engineering
Former German standard for instrumentation code letters, withdrawn. Replaced by DIN EN 62424 and DIN 28000-4; older P&IDs still show its notation.
- ISO 3511 – Process measurement and control functions – Symbolic representation
Former ISO standard for instrumentation symbols, withdrawn in April 2025; successor ISO 14617-2:2025. In Germany DIN EN 62424 applies.
- IEC 61346 – Industrial systems – Structuring principles and reference designations (old)
Predecessor of IEC 81346, withdrawn. Older designation guidelines still refer to it.
- DIN 6779 – Designation system for technical products and technical product documentation
Former German designation standard. Parts 1, 2 and 10 are withdrawn and have been merged into DIN EN IEC 81346 and ISO/TS 81346-10.
- ISO/TS 16952 – Technical product documentation – Reference designation system
Former ISO specification for reference designation; part 10 was the version for power plants (RDS-PP). Now listed as ISO/TS 81346-10.
- B 105/B 106 – VGB guidelines on KKS
Former VGB guidelines on the power plant identification system (KKS). Today the standard VGB-S-811-01 applies.
- GPSG – German Equipment and Product Safety Act (GPSG)
Former German product safety act. It applied until 2011 and was replaced by the Product Safety Act (ProdSG).
- DIN 2470 – Gas pipelines made of steel pipes up to 16 bar – Requirements for pipeline components
Old standard for gas pipelines, withdrawn. Today DIN EN 12007 applies (gas infrastructure up to 16 bar), and DIN EN 13480 for industrial plants.
- DIN 1626 – Welded circular tubes of non-alloy steels with specified requirements
Old German pipe standard, withdrawn. Its successor is DIN EN 10217-1; depending on the application also DIN EN 10224, DIN EN 10296-1 or DIN EN ISO 3183. Designations according to DIN 1626 are still found in existing plants and old pipe specs.
- DIN 2458 – Welded steel tubes – Dimensions, masses per unit length
Former German dimension standard for welded steel pipes, withdrawn and, like DIN 2448, replaced by DIN EN 10220.
- DIN 2413 – Seamless steel tubes for oil and water hydraulic systems – Calculation basis
Today it only applies to hydraulic pipes under pulsating load. The former parts 1 and 2 for general piping are withdrawn; there the calculation follows DIN EN 13480-3.
- DIN 50049 – Metallic products – Types of inspection documents (old)
Predecessor of DIN EN 10204, withdrawn. Old designations such as “3.1B” and “3.1C” correspond today to 3.1 and 3.2.
- DIN 2513 – Spigot and recess on flanges, PN 10 to 100
Old standard for flanges with spigot and recess, withdrawn. Today these sealing faces are called type E and F in DIN EN 1092-1.
- DIN EN 1591 – Flanges and their joints – Design rules for gasketed circular flange connections
Calculation method for tight and strong flange connections (part 1). The gasket parameters are provided by DIN CEN/TR 1591-2 or DIN EN 13555; part 4 (now DIN CEN/TS 1591-4) covers the qualification of fitters.
- CR – CEN Report
Report from CEN (CEN Report). Such documents are now called CEN/TR (Technical Report).
- DIN 6771 – Title blocks for drawings, plans and lists (old)
Former standard for title blocks, withdrawn and replaced by DIN EN ISO 7200. Many company title blocks are still based on it.
- B36.10M – ASME B36.10M Steel Pipe
US dimensional standard for welded and seamless steel pipes: outside diameters and wall thicknesses (schedule).
- B36.19 – ASME B36.19
US dimensional standard for stainless steel pipe: outside diameters and wall thicknesses (schedule with “S”, e.g. 10S).
- B16.5 – ASME B16.5 Flanges
US standard for flanges and flanged fittings from NPS ½ to NPS 24 in pressure classes Class 150 to 2500.
- B16.9 – ASME B16.9
US standard for butt-welding fittings: elbows, tees, reducers and caps.
- B31.3 – ASME B31.3 Process Piping
US code for process piping: materials, design, fabrication and testing of piping in chemical and process plants.
- DIN EN 593 – Industrial valves – Metallic butterfly valves
Product standard for metallic butterfly valves (concentric and eccentric, wafer and flanged type).
A new edition is announced for 2026-11; until then the 2018-01 edition applies.
Sources and origins
- ISO – International Organization for Standardization (for R&I, ISO, PE, A0 … A4, SDR, IFC)
- IEC – International Electrotechnical Commission (for R&I, CAEX, SIL, RDS-PP, DCC, IEC)
- CEN and CENELEC – European standardization (for EN, PN, P235GH)
- CEN and CENELEC (for CEN, B1, B2, CR)
- DIN – German Institute for Standardization (for DIN, DN, PN, P235GH)
- Austrian Standards (for ÖNORM)
- SNV (for SN)
- NEN (for NEN)
- BSI Group (for BS)
- AFNOR (for NF)
- UNE (for UNE)
- DIN Media: DIN 21057-1:2023-08 (for DIN 21057)
- TRGS 201 Annex 3, Table 2: Marking of pipelines according to the fluids conveyed (BGN, in German) (for DIN 2403)
- DIN Media: DIN 2403:2025-12 (for DIN 2403)
- VdTÜV – TÜV Association (for AD 2000)
- Federal Institute for Occupational Safety and Health (BAuA) – Technical Rules (for TRBS)
- EUR-Lex – access to EU law (for EU, ATEX, PS)
- DIN Media: DIN EN 13480-1:2024-12 (for DIN EN 13480)
- AwSV (Gesetze im Internet) (for AwSV)
- German Environment Agency (for TA Luft)
- DIN Media: VDI 2290 (for VDI 2290)
- Wikipedia – Computer-aided design (for CAD)
- ISO 6708 – Pipework components, definition and selection of DN (for DN)
- BIPM – International System of Units (SI) (for bar, MPa, N/mm²)
- DIN Media: DIN EN ISO 6708:1995-09 (for DIN EN ISO 6708)
- DIN Media: DIN EN 1333:2006-06 (for DIN EN 1333)
- DIN Media: DIN EN 764-1:2016-12 (for DIN EN 764)
- ISO 80000-1:2022 (for ISO 80000)
- DIN Media: DIN EN 10220:2003-03 (for DIN EN 10220, DIN 2448)
- DIN Media: DIN EN 1057:2010-06 (for DIN EN 1057)
- DIN Media: DIN EN 1092-1:2018-12 (for DIN EN 1092)
- DIN Media: DIN EN ISO 10628-1:2015-04 (for DIN EN ISO 10628)
- DIN Media: DIN 28000-4:2014-07 (for DIN 28000)
- DIN Media: DIN 2429-1 (withdrawn) (for DIN 2429)
- ISO 14617-1:2025 (for ISO 14617)
- ISO 15519-1:2010 (for ISO 15519)
- DIN Media: DIN EN 62424:2017-12 (for DIN EN 62424)
- ANSI Webstore: ANSI/ISA-5.1-2024 (for ANSI/ISA-5.1)
- Wikipedia: United States (for US)
- ISA – International Society of Automation (for ISA)
- IEC Webstore: IEC 60617 database (for IEC 60617)
- DIN Media: DIN EN 61511-1:2019-02 (for DIN EN 61511)
- DIN Media: DIN EN 61508-1 (for DIN EN 61508)
- DIN Media: DIN EN ISO 7200:2004-05 (for DIN EN ISO 7200)
- DIN Media: DIN EN ISO 5457:2017-10 (for DIN EN ISO 5457)
- Autodesk – DWG (for DWG)
- DIN Media: DIN EN ISO 3098-1:2015-06 (for DIN EN ISO 3098)
- DIN Media: DIN EN ISO 128-2:2023-06 (for DIN EN ISO 128)
- DIN Media: DIN ISO 5455 (for DIN ISO 5455)
- DIN Media: DIN EN ISO 13567-1:2018-02 (for DIN EN ISO 13567)
- DIN Media: DIN EN IEC 81346-1:2024-07 (for DIN EN IEC 81346)
- vgbe energy (formerly VGB PowerTech) (for KKS, RDS-PP)
- DIN Media: DIN EN ISO 7010 (for DIN EN ISO 7010)
- DIN Media: DIN EN 10216-1:2014-03 (for DIN EN 10216)
- DIN Media: DIN EN 10253-2:2026-07 (for DIN EN 10253)
- DIN Media: DIN EN 1514-1:2024-10 (for DIN EN 1514)
- DIN Media: DIN EN 1515-1:2000-01 (for DIN EN 1515)
- DIN Media: DIN EN 13555:2021-04 (for DIN EN 13555)
- DIN Media: DIN EN 736-1:2018-05 (for DIN EN 736)
- DIN Media: DIN EN 19:2024-03 (for DIN EN 19)
- DIN Media: DIN EN 1983:2013-12 (for DIN EN 1983)
- DIN Media: DIN EN ISO 4126-1 (for DIN EN ISO 4126)
- DIN Media: DIN EN 14917:2022-02 (for DIN EN 14917)
- DIN Media: DIN EN 10226-1:2004-10 (for DIN EN 10226)
- DIN Media: DIN EN ISO 228-1:2003-05 (for DIN EN ISO 228)
- DIN Media: DIN EN 10255:2007-07 (for DIN EN 10255)
- DIN Media: DIN EN 10241:2000-08 (for DIN EN 10241)
- DIN Media: DIN EN 10242:2026-02 (for DIN EN 10242)
- DIN Media: DIN EN ISO 15494:2021-05 (for DIN EN ISO 15494)
- DIN Media: DIN EN ISO 15493:2017-07 (for DIN EN ISO 15493)
- DIN Media: DIN EN 12201-2:2025-03 (for DIN EN 12201)
- ISO 6412-1:2017 (for ISO 6412)
- DIN Media: DIN EN ISO 3834-1:2022-01 (for DIN EN ISO 3834)
- DIN Media: DIN EN ISO 9606-1:2017-12 (for DIN EN ISO 9606)
- DIN Media: DIN EN ISO 15614-1:2020-05 (for DIN EN ISO 15614)
- DIN Media: DIN EN ISO 5817:2023-07 (for DIN EN ISO 5817)
- DIN Media: DIN EN ISO 17636-1:2022-10 (for DIN EN ISO 17636)
- DIN Media: DIN 4140:2023-05 (for DIN 4140)
- AGI (for AGI)
- DIN Media: VDI 2055 part 1:2025-10 (for VDI 2055)
- DIN Media: DIN EN ISO 12944-1:2019-01 (for DIN EN ISO 12944)
- DIN Media: DIN EN IEC 60079-10-1:2022-02 (for DIN EN IEC 60079-10)
- DIN Media: DIN EN 1672-2:2021-05 (for DIN EN 1672)
- EHEDG (for EHEDG)
- DIN Media: DIN 11850 (for DIN 11850)
- DIN Media: DIN EN 1775:2007-10 (for DIN EN 1775)
- DIN Media: DVGW G 459-1 (A):2026-07 (for DVGW G 459)
- DIN Media: DIN EN 12007-1:2012-10 (for DIN EN 12007)
- DIN Media: DIN EN 253:2024-10 (for DIN EN 253)
- DIN Media: DIN EN 13941-1:2022-06 (for DIN EN 13941)
- DIN Media: DIN EN 806-1:2001-12 (for DIN EN 806)
- DIN Media: DIN 1988-100:2011-08 (for DIN 1988)
- DIN Media: DIN EN 378-1:2021-06 (for DIN EN 378)
- DIN Media: DIN EN 1443 (for DIN EN 1443)
- DIN Media: EN 1856-1 (for DIN EN 1856)
- DIN Media: DIN 11864-1:2025-04 (for DIN 11864)
- DIN Media: DIN EN ISO 19650-1:2019-08 (for DIN EN ISO 19650)
- buildingSMART International (for BIM, IFC)
- DIN Media: DIN EN ISO 16739-1:2024-09 (for DIN EN ISO 16739)
- DEXPI (for DEXPI)
- ISO 15926-1:2004 (for ISO 15926)
- IEC Webstore: IEC 81355-1 (for IEC 81355)
- DIN Media: DIN EN 82045-1:2002-11 (for DIN EN 82045)
- DIN Media: VDI 2770 part 1:2020-04 (for VDI 2770)
- NAMUR (for NE)
- DIN Media: DIN EN 62424 (VDE 0810-24) (for VDE 0810)
- ANSI – American National Standards Institute (for ANSI)
- DIN Media: DIN IEC 60050-351:2014-09 (for DIN IEC 60050)
- DIN Media: DIN 19226-1 (withdrawn) (for DIN 19226)
- IEC Webstore: IEC 61355-1 (for IEC 61355)
- DIN Media: DIN EN 10217-1:2019-08 (for DIN EN 10217)
- DIN Media: DIN EN ISO 3183:2020-02 (for DIN EN ISO 3183)
- DIN Media: DIN EN 10208-2 (withdrawn) (for DIN EN 10208)
- DIN Media: DIN 2448 (withdrawn) (for DIN 2448)
- DIN Media: DIN EN 10204:2005-01 (for DIN EN 10204)
- ISO 15608 (for ISO 15608)
- DIN Media: DIN 19227-1 (withdrawn) (for DIN 19227)
- ISO 3511-1 (for ISO 3511)
- IEC Webstore: IEC 61346-1:1996 (withdrawn) (for IEC 61346)
- DIN Media: DIN 6779-1 (withdrawn) (for DIN 6779)
- ISO/TS 16952-10:2008 (for ISO/TS 16952)
- vgbe energy (for B 105/B 106)
- Gesetze im Internet (for GPSG)
- DIN Media: DIN 2470-1 (withdrawn) (for DIN 2470)
- DIN Media: DIN 1626 (withdrawn) (for DIN 1626)
- DIN Media: DIN 2458 (withdrawn) (for DIN 2458)
- DIN Media: DIN 2413:2020-04 (for DIN 2413)
- DIN Media: DIN 50049 (withdrawn) (for DIN 50049)
- DIN Media: DIN 2513 (withdrawn) (for DIN 2513)
- DIN Media: DIN EN 1591-1:2026-02 (for DIN EN 1591)
- DIN Media: DIN 6771-1 (withdrawn) (for DIN 6771)
- ASME – American Society of Mechanical Engineers (for B36.10M, B16.5, B31.3)
- ASME (for B36.19, B16.9)
- DIN Media: DIN EN 593 (for DIN EN 593)